<?xml version="1.0" encoding="UTF-8"?>
<rss version="2.0" xmlns:atom="http://www.w3.org/2005/Atom" xmlns:dc="http://purl.org/dc/elements/1.1/">
  <channel>
    <title>DEV Community: Kina Zeng - Runhee Packaging</title>
    <description>The latest articles on DEV Community by Kina Zeng - Runhee Packaging (@runhee).</description>
    <link>https://dev.to/runhee</link>
    <image>
      <url>https://media2.dev.to/dynamic/image/width=90,height=90,fit=cover,gravity=auto,format=auto/https:%2F%2Fdev-to-uploads.s3.us-east-2.amazonaws.com%2Fuploads%2Fuser%2Fprofile_image%2F4242085%2F70d1b7de-7728-4713-a1aa-bd81d3d152d7.jpg</url>
      <title>DEV Community: Kina Zeng - Runhee Packaging</title>
      <link>https://dev.to/runhee</link>
    </image>
    <atom:link rel="self" type="application/rss+xml" href="https://dev.to/feed/runhee"/>
    <language>en</language>
    <item>
      <title>Paperboard Hanger Physics: Caliper Benchmarking &amp; 1.5kg Load Engineering</title>
      <dc:creator>Kina Zeng - Runhee Packaging</dc:creator>
      <pubDate>Fri, 20 Nov 2026 05:50:52 +0000</pubDate>
      <link>https://dev.to/runhee/paperboard-hanger-physics-caliper-benchmarking-15kg-load-engineering-4jhk</link>
      <guid>https://dev.to/runhee/paperboard-hanger-physics-caliper-benchmarking-15kg-load-engineering-4jhk</guid>
      <description>&lt;p&gt;Retail garment supply chains inside the EU are midway through a forced material substitution. Regulation (EU) 2025/40 — the Packaging and Packaging Waste Regulation — attaches recyclability, recycled-content and reusability obligations to every packaging component that crosses a member-state border, and the garment hanger is an awkward case. It is a structural part, not a decorative one. The properties it has to deliver are mechanical: flexural stiffness at the shoulder line, creep resistance under static load, and dimensional stability across the humidity band of a retail floor.&lt;/p&gt;

&lt;p&gt;Most de-plasticisation scoping stops at material availability and skips the beam calculation. A loaded hanger is a cantilever — a concentrated point load at the shoulder, a fixed support at the hook, and a span that has to stay flat for as long as the garment sits on the rail. Extruded PS and ABS satisfy that load with section geometry: moulded I-beam profiles, gusseted shoulders, wall thickness tuned against a flexural modulus in the 2.0–2.6 GPa range. Cellulose fibre sits roughly an order of magnitude lower and, more critically, it creeps. Under sustained load in the 45–65 % RH band typical of retail floors and distribution centres, the fibre network relaxes, the neutral axis migrates, and the section takes permanent set.&lt;/p&gt;

&lt;p&gt;Dongguan Runhee Paper Products (&lt;a href="https://www.runhee.com/" rel="noopener noreferrer"&gt;Dongguan Runhee Paper Products&lt;/a&gt;) has spent 16 years cold-pressing multi-ply high-density kraft board as single units — one stacked ply set, one press cycle, no laminated core, no plastic insert — and the bench data accumulated across that period is the reason a paper hanger can now be specified as a structural component rather than a display prop.&lt;/p&gt;

&lt;h2&gt;
  
  
  Caliper benchmarking: 2.5 mm vs 3.2–3.8 mm
&lt;/h2&gt;

&lt;p&gt;Load case: 1.5 kg static mass suspended at the shoulder midpoint of a 415 mm adult coat profile, 72 h duration, 23 °C / 50 % RH, tip deflection logged at 0 h, 1 h, 24 h, 48 h and 72 h. The 2.5 mm family is 4-ply at roughly 250 gsm per ply. The 3.5 mm family is 6-ply and runs 3.2–3.8 mm across the pressed blank after caliper recovery.&lt;/p&gt;

&lt;div class="table-wrapper-paragraph"&gt;&lt;table&gt;
&lt;thead&gt;
&lt;tr&gt;
&lt;th&gt;Caliper&lt;/th&gt;
&lt;th&gt;Ply build&lt;/th&gt;
&lt;th&gt;Tip deflection @ 72 h&lt;/th&gt;
&lt;th&gt;Permanent set, 24 h post-load&lt;/th&gt;
&lt;th&gt;Shoulder angle loss&lt;/th&gt;
&lt;/tr&gt;
&lt;/thead&gt;
&lt;tbody&gt;
&lt;tr&gt;
&lt;td&gt;2.5 mm&lt;/td&gt;
&lt;td&gt;4-ply / 250 gsm&lt;/td&gt;
&lt;td&gt;9.6 mm&lt;/td&gt;
&lt;td&gt;4.3 mm&lt;/td&gt;
&lt;td&gt;2.7°&lt;/td&gt;
&lt;/tr&gt;
&lt;tr&gt;
&lt;td&gt;3.5 mm (3.2–3.8)&lt;/td&gt;
&lt;td&gt;6-ply / 250 gsm&lt;/td&gt;
&lt;td&gt;3.0 mm&lt;/td&gt;
&lt;td&gt;0.4 mm&lt;/td&gt;
&lt;td&gt;0.6°&lt;/td&gt;
&lt;/tr&gt;
&lt;/tbody&gt;
&lt;/table&gt;&lt;/div&gt;

&lt;p&gt;The 2.5 mm section is not elastic-bending at 1.5 kg — it is creep-bending. Of its 9.6 mm total deflection, 3.4 mm appears in the first hour and a further 4.1 mm accumulates between hours 1 and 24. That split is the diagnostic. Elastic response taken in the first hour is recoverable; the creep component is not, and the 4.3 mm permanent set left after de-loading is a straight loss of shoulder geometry. At 1.5 kg the 2.5 mm caliper is outside its service envelope.&lt;/p&gt;

&lt;p&gt;The 3.5 mm section stays inside the elastic regime for most of the load case: 1.1 mm in the first hour, 1.2 mm of creep to hour 24, and a 0.4 mm residual set that sits under the 1 mm threshold where the hanger returns to nominal geometry on the rail. The failure mode moves as well. Above 3.2 mm the limiting defect is no longer global bending but localised ply delamination at the shoulder radius, which is a press-parameter problem — tonnage ramp and dwell — rather than a material one.&lt;/p&gt;

&lt;p&gt;The &lt;a href="https://www.runhee.com/product/eco-kraft-paper-hanger-for-adult-coats-jackets" rel="noopener noreferrer"&gt;heavy-duty cardboard coat hangers&lt;/a&gt; line runs the 3.5 mm caliper as standard and returns the same curve: sub-4 mm tip deflection at 1.5 kg over 72 h, with the coated shoulder radius carrying the load path instead of the hook collar. The 2.5 mm caliper keeps a valid use case, but that case is a 600–800 g garment, not a coat.&lt;/p&gt;

&lt;h2&gt;
  
  
  Die cutting, tooling, and the freight TCO
&lt;/h2&gt;

&lt;p&gt;Forming is CNC cold-press flat-bed die cutting. A steel-rule die is nested against the blank, the platen presses the ply stack at controlled tonnage, and caliper setting plus fold-line crushing happen in the same cycle. There is no injection moulding tooling outlay in the cost model at all — no cavity, no core, no ejector stack, no melt-flow simulation. A steel-rule die runs a fraction of a mould's cost and clears in days rather than the 4–6 weeks an injection tool takes, so short and mid-run SKUs stop carrying an amortised tooling line. The same &lt;a href="https://www.runhee.com/customization" rel="noopener noreferrer"&gt;flexible paperboard customization&lt;/a&gt; route lets a profile change be handled as a die change rather than a new tool.&lt;/p&gt;

&lt;p&gt;Unit mass follows the caliper: 18 g to 35 g per finished hanger across the current profile range, against 22–45 g for the assembled ABS parts it replaces.&lt;/p&gt;

&lt;p&gt;The freight number is the one procurement tends to miss. Flat blanks ship flat and the hook is formed by a single fold at destination, so cartons are packed with corrugated dividers instead of void fill. Measured across three FCL shipments, the same SKU count occupies 42–46 % less container cube than assembled plastic hangers — a direct 42–46 % cut in the ocean-leg volume charge and in the carbon footprint attributed to that leg, not a modelling estimate.&lt;/p&gt;

&lt;h2&gt;
  
  
  Reproducibility notes
&lt;/h2&gt;

&lt;p&gt;The test rig is a fixed steel hook on a rigid frame, load applied through a calibrated 1.5 kg mass, deflection read with a dial indicator at the shoulder tip to 0.01 mm. Humidity is held for 4 h before load application so fibre moisture content is at equilibrium. Permanent set is read 24 h after de-loading, at the same humidity. Anyone repeating the run should log the 1 h split explicitly — a 72 h endpoint alone hides whether the section failed elastically or crept.&lt;/p&gt;




&lt;p&gt;&lt;strong&gt;Kina Zeng&lt;/strong&gt; - Dongguan Runhee Paper Products, Packaging Engineering Lab. Email: &lt;code&gt;alice.wang@runhee.com&lt;/code&gt;&lt;/p&gt;

</description>
      <category>engineering</category>
      <category>materials</category>
      <category>manufacturing</category>
      <category>sustainability</category>
    </item>
  </channel>
</rss>
