<?xml version="1.0" encoding="UTF-8"?>
<rss version="2.0" xmlns:atom="http://www.w3.org/2005/Atom" xmlns:dc="http://purl.org/dc/elements/1.1/">
  <channel>
    <title>DEV Community: Shunlongwei Co., Ltd.</title>
    <description>The latest articles on DEV Community by Shunlongwei Co., Ltd. (@shunlongwei).</description>
    <link>https://dev.to/shunlongwei</link>
    <image>
      <url>https://media2.dev.to/dynamic/image/width=90,height=90,fit=cover,gravity=auto,format=auto/https:%2F%2Fdev-to-uploads.s3.us-east-2.amazonaws.com%2Fuploads%2Fuser%2Fprofile_image%2F4258631%2F8eb00ae7-4f9a-4b37-8c06-b3bfe125933e.jpg</url>
      <title>DEV Community: Shunlongwei Co., Ltd.</title>
      <link>https://dev.to/shunlongwei</link>
    </image>
    <atom:link rel="self" type="application/rss+xml" href="https://dev.to/feed/shunlongwei"/>
    <language>en</language>
    <item>
      <title>IGBT Module Offline Multimeter Bench Check: Static Verification Before Power-Up</title>
      <dc:creator>Shunlongwei Co., Ltd.</dc:creator>
      <pubDate>Sun, 22 Nov 2026 11:07:20 +0000</pubDate>
      <link>https://dev.to/shunlongwei/igbt-module-offline-multimeter-bench-check-static-verification-before-power-up-3ekl</link>
      <guid>https://dev.to/shunlongwei/igbt-module-offline-multimeter-bench-check-static-verification-before-power-up-3ekl</guid>
      <description>&lt;p&gt;Before installing an IGBT module into an industrial motor drive, inverter, or power stage, a quick offline multimeter check prevents secondary driver-board damage caused by shorted dies or degraded gate oxide.&lt;/p&gt;

&lt;h2&gt;
  
  
  1. Safety &amp;amp; ESD Preparation
&lt;/h2&gt;

&lt;ul&gt;
&lt;li&gt;Discharge DC-link capacitors completely and verify zero bus voltage before disconnecting busbars.&lt;/li&gt;
&lt;li&gt;Use an ESD wrist strap or grounded mat before handling gate (&lt;code&gt;G&lt;/code&gt;) and auxiliary emitter (&lt;code&gt;E_aux&lt;/code&gt;) pins.&lt;/li&gt;
&lt;/ul&gt;

&lt;h2&gt;
  
  
  2. Gate-Emitter (&lt;code&gt;G-E&lt;/code&gt;) Integrity
&lt;/h2&gt;

&lt;ul&gt;
&lt;li&gt;Set your digital multimeter to resistance (&lt;code&gt;Ω&lt;/code&gt; / &lt;code&gt;MΩ&lt;/code&gt;).&lt;/li&gt;
&lt;li&gt;Probe between Gate and Emitter: a healthy insulated gate reads open circuit (&lt;code&gt;OL&lt;/code&gt; or &lt;code&gt;&amp;gt;10 MΩ&lt;/code&gt;, unless the datasheet specifies an integrated gate-emitter bleeder resistor).&lt;/li&gt;
&lt;li&gt;Very low resistance or a dead short across &lt;code&gt;G-E&lt;/code&gt; indicates gate oxide punch-through.&lt;/li&gt;
&lt;/ul&gt;

&lt;h2&gt;
  
  
  3. Collector-Emitter (&lt;code&gt;C-E&lt;/code&gt;) &amp;amp; Freewheeling Diode Check
&lt;/h2&gt;

&lt;ul&gt;
&lt;li&gt;Switch the multimeter to &lt;strong&gt;Diode&lt;/strong&gt; mode.&lt;/li&gt;
&lt;li&gt;Forward-bias the anti-parallel freewheeling diode (&lt;code&gt;E → C&lt;/code&gt; for N-channel IGBT): typical forward voltage drop &lt;code&gt;Vf&lt;/code&gt; is &lt;code&gt;0.35 V – 0.65 V&lt;/code&gt; at room temperature.&lt;/li&gt;
&lt;li&gt;Reverse direction (&lt;code&gt;C → E&lt;/code&gt;) with &lt;code&gt;G&lt;/code&gt; shorted to &lt;code&gt;E&lt;/code&gt;: must read &lt;code&gt;OL&lt;/code&gt; (blocking).&lt;/li&gt;
&lt;/ul&gt;

&lt;h2&gt;
  
  
  4. Baseplate Isolation Check
&lt;/h2&gt;

&lt;ul&gt;
&lt;li&gt;Confirm electrical isolation between all power terminals (&lt;code&gt;C&lt;/code&gt;, &lt;code&gt;E&lt;/code&gt;, &lt;code&gt;AC&lt;/code&gt;) and the copper/AlSiC mounting baseplate before torquing onto the heatsink.&lt;/li&gt;
&lt;/ul&gt;




&lt;p&gt;&lt;em&gt;Extended engineering reference &amp;amp; troubleshooting guide: &lt;a href="https://www.slw-ele.com/a-practical-guide-to-testing-igbt-modules-with-a-multimeter.html" rel="noopener noreferrer"&gt;A Practical Guide to Testing IGBT Modules with a Multimeter&lt;/a&gt;&lt;/em&gt;&lt;/p&gt;

</description>
      <category>electronics</category>
      <category>hardware</category>
      <category>engineering</category>
      <category>troubleshooting</category>
    </item>
  </channel>
</rss>
