DEV Community

Mingchun Huang
Mingchun Huang

Posted on Edited on

0.005 mm: When a Tight Tolerance Actually Matters, and When ISO 2768-m Is Enough

Buyer asks: "Can you hold ±0.005 mm?" Shop says yes. Quote doubles. Sometimes that's real process cost. Sometimes it's theater. Here is how to tell the difference before you pay for it.

The question behind the question

A tolerance is only "tight" relative to what the process naturally holds. On a CNC machining center, a well-maintained setup holds ±0.01 mm between features on the same part without any special effort — that's just what the machine does when everything is clean and the tooling is fresh. When a customer asks for ±0.005 mm, we ask one question first: what is this dimension actually doing in your assembly?

Three honest answers we hear:

  1. It's a bearing seat or a press-fit pin. The fit class genuinely depends on it. ±0.005 mm is real, and worth paying for.
  2. The tolerance came from a default CAD setting. Somebody typed a number in 2019 and nobody questioned it. ±0.005 mm is real money for nothing.
  3. It's on a cosmetic face. Visual appearance is driven by surface finish and witness marks, not linear tolerance. A ±0.05 mm callout with a Ra 0.8 finish requirement is often the correct spec.

What actually changes when you tighten the number

Going from ±0.01 mm to ±0.005 mm is not "twice as careful." It changes the production system:

  • Inspection method. Calipers and micrometers stop being the referee. You move to CMM or dedicated gauging, and every part (not a sample) gets measured on critical features.
  • Tool life management. Tools get changed on a schedule keyed to actual wear data, not visual checks, because a worn end mill drifts measurably within its last percent of life.
  • Thermal control. On longer parts, spindle and ambient heat become the dominant error source. Warm-up cycles and coolant temperature control enter the conversation.
  • Fixture quality. Generic vises give way to dedicated fixtures or zero-point systems so that datum repeatability doesn't eat the tolerance budget.

None of this is fake cost. But it's also not linear — and it only applies to the dimensions that genuinely need it.

Where the tolerance budget goes on a typical aluminum housing

Feature type Realistic driver Sensible tolerance
Bearing bore, press-fit pin Fit class in the assembly ±0.005 mm
Mating face flatness Gasket sealing, leak paths ±0.01–0.02 mm
General machined dimensions Appearance, clearance ISO 2768-m
Cosmetic outer surfaces Anodizing appearance ±0.05 mm + Ra callout
Thread positions Fastener assembly ISO 2768-m

Note the pattern: the tight number belongs to functional interfaces, and general dimensions fall back to a recognized general-tolerance standard. A drawing where every dimension reads ±0.005 mm usually means the engineer didn't triage.

How to spec it so quotes come back sane

  • Put ±0.005 mm (or tighter, only where the assembly genuinely requires it) on functional bores, shafts, and datum features — and reference the datum scheme on the drawing.
  • Leave general dimensions to ISO 2768-m unless the assembly dictates otherwise. It's a real, auditable standard, not a shortcut.
  • Tell the shop why the tight dimension matters. "This is the bearing seat" lets the machinist prioritize process decisions correctly. "Tighten everything" doesn't.
  • If a supplier quotes flat pricing across both cases without asking which dimensions are critical, ask them what inspection plan they priced. That answer reveals whether the tolerance was taken seriously.

Conclusion

±0.005 mm is not expensive because machines can't do it — it's expensive because of the inspection, tooling, and thermal discipline that surround it. The cheapest drawings pay tight tolerances only where the assembly pays them back: fits, seals, and datums. Everything else rides on ISO 2768-m, and your quote gets better for it.


This article is from CHX Precision Metal, a Shenzhen CNC machining shop running 70 Tsugami Swiss-type lathes (Ø1–20 mm) among 220 CNC machines. Prototypes in 3–7 days, production in 7–15 days, MOQ from 1 piece with volume-based pricing. Shipping: EXW Shenzhen only - we are happy to recommend reliable freight forwarders. Technical library and capabilities: https://chxmetal.com

Related reading

More notes from the same shop floor, for buyers comparing processes or suppliers:

Top comments (0)