DEV Community

Ray Wang
Ray Wang

Posted on Edited on

ASTM A358 Classes 1-5: The Two Axes Most Purchase Orders Get Wrong

Most arguments about ASTM A358 pipe start from the same wrong assumption: that Classes 1 through 5 form a ladder from "basic" to "best". They do not. Section 1.3 defines the classes on two independent axes - how the longitudinal seam is welded, and how much of that seam is radiographed. Everything else, including price differences that look arbitrary on a quotation, follows from those two variables.

Here is what each class actually obliges, where the widely copied supplier summaries go wrong, and what to put on the purchase order so a mill cannot ship pipe that is compliant with a class you never asked for.

Axis one: weld construction

Double welded means filler metal is deposited from both sides of the joint. Single welded means one side only. This is a fabrication decision, not a quality grade: a single-welded joint with full radiography is not "worse" than a double-welded joint with none - it is a different joint for a different access condition.

Axis two: radiography coverage

Complete, spot, or none. "Complete" means all welded joints are examined. "Spot" is a defined coverage rate. "None" is exactly that, and it is legal under Class 2.

Class Weld construction Filler metal Radiography
1 Double welded In all passes Complete
2 Double welded In all passes None required
3 Single welded In all passes Complete
4 Single welded In all passes, except the inside pass may be made without filler metal Complete
5 Double welded In all passes Spot

Three statements that contradict the standard

A surprising number of supplier pages state that Class 1 is single welded with 100% radiography, that Class 3 is double welded with 100% radiography, and that Class 5 is an autogenous weld with no filler metal. All three are inverted relative to the specification text:

  • Class 1 is double welded, filler metal in all passes, fully radiographed.
  • Class 3 is single welded, filler metal in all passes, fully radiographed.
  • Class 5 is double welded, filler metal in all passes, spot radiographed.

Autogenous welding does appear in A358, but only as the permitted exception for the inside pass of Class 4, under 6.2.2.1 and 6.2.2.2. If a data sheet or a quotation tells you Class 1 is single welded, the document was not written against the standard. Ask for the clause reference - a supplier who cannot produce one has been copying the same wrong summary everyone else copied.

"Spot radiographed" is a number, not a mood

Clause 16.2 sets the floor: not less than 12 in. [300 mm] of radiograph for every 50 ft [15 m] of weld. A supplier offering "spot RT" without that coverage rate is not offering Class 5, whatever the certificate says.

There is a second trap. Acceptance criteria differ by coverage: Class 1, 3 and 4 joints are judged to ASME BPVC Section VIII Div. 1 UW-51, while Class 5 joints are judged to UW-52. A Class 5 joint is therefore not a Class 1 joint examined less often - the film is evaluated against a different clause with different acceptance limits.

Heat treatment and the HT stencil

Unless the order says otherwise, pipe is furnished heat treated per Table 2, which for the general case means 1900 F [1040 C]. When a lower final heat-treatment temperature is agreed, clause 6.3.2.1 requires every length to be stencilled with the actual final temperature followed by the suffix HT. That stencil is the only field evidence of what the pipe actually saw, as opposed to what the purchase order assumed.

For stabilised grades - 321, 321H, 347, 347H, 348 - Supplementary Requirement S5 adds a stabilisation treatment after the initial solution anneal. S6, when invoked, requires intergranular corrosion testing to ASTM A262 Practice E, and for titanium- or columbium-bearing grades S6 can make S5 necessary to comply.

What belongs on the purchase order

  1. The class number, quoted with the clause basis, not just "Class 1".
  2. Radiography coverage and the acceptance clause that applies to it.
  3. Heat-treatment temperature, and whether the HT stencil is required.
  4. Supplementary requirements S1 to S6, called out individually - they never apply automatically.
  5. ASTM A999/A999M as the general requirements reference.
  6. Grade and plate chemistry source (Table 1 chemistry is taken from A240/A240M).

Most disputes I have seen on EFW stainless pipe trace back to one of those six lines being left implicit. The standard is unambiguous; the order text usually is not.

Why this matters most above NPS 24

A358 is written around plate-formed, longitudinally welded cylinders, which is why it is the natural specification for large-diameter and heavy-wall stainless work: desalination trains, FGD ducting, column shells, high-temperature headers. A312 covers the smaller and more conventional range, and A778 covers another corner again. Choosing between them is a separate decision from choosing a class, and mixing the two up is how projects end up with the right grade in the wrong specification.

Further reading, if you want the clause-level detail:

Top comments (0)