DEV Community

Ray Wang
Ray Wang

Posted on

How a 5000 mm Stainless Steel Pipe Is Actually Built: JCOE, LSAW and the Multi-Seam Problem

Ask five suppliers what "JCOE" means and you will usually get five slightly different answers. Most of them describe it as a welding process. It is not. This is the single most common mix-up in large-diameter pipe procurement, and it matters because it decides which questions you should be asking about the weld.

Two different machines, two different jobs

A large-diameter stainless pipe line is not one process. It is a forming step followed by a welding step:

  • JCOE is the forming method. A plate is pressed progressively into a "J", then a "C", then an "O", and finally expanded ("E") so the two edges meet with the correct gap and the finished roundness is within tolerance.
  • LSAW (longitudinal submerged arc welding) is the welding method that closes that seam, usually with a gas tungsten arc root pass and submerged arc fill passes.

So JCOE and LSAW are not competitors. JCOE makes the shape; LSAW makes the joint. A supplier who tells you "we weld by JCOE" is describing their press, not their welding procedure — and you should ask for the WPS/PQR instead.

Why one section stops at 3 m

The hard limit on a single JCOE section is not the welding machine. It is the plate.

Commercial stainless plate arrives in widths that, after edge trimming and the forming allowance, support a formed section of roughly 3 m in length. Anything longer needs either a wider plate (which the mill does not stock in that grade and thickness) or a second longitudinal seam.

That is why a "3 m single section" is a real specification rather than a marketing number: it is the largest piece that can be formed from one plate with one longitudinal weld.

Going past 3000 mm OD: the multi-seam build-up

Once the outside diameter moves beyond what one formed section can cover, the pipe is not made bigger — it is made from more pieces.

A 5000 mm OD pipe is assembled from several formed segments, each closed by its own longitudinal seam and then joined to the next by circumferential (girth) seams. In practice this means:

  • 3 longitudinal seams plus 2 girth seams for a 3-segment assembly;
  • every seam individually welded, inspected and recorded;
  • the girth seams being the ones that decide roundness at the ends, because each circumferential weld pulls slightly as it cools.

For a buyer this changes the acceptance conversation completely. You are no longer inspecting "a weld". You are inspecting a defined set of welds, each with its own RT film or UT record, and you need the drawing to tell you how many there are.

Welding details that actually travel with the pipe

On austenitic stainless (304/304L, 316/316L, 321, 347), a workable large-diameter procedure normally looks like this:

Item Typical practice
Root pass GTAW, argon backing or trailing shield, oxygen below 50 ppm at arc start
Fill / cap SAW with matching filler (ER308L, ER316L, ER347)
Preheat None for austenitic grades
Interpass temperature Capped, commonly 150 °C max, to limit sensitisation
Post-weld Solution anneal at 1040 °C for thicker walls, or stabilisation for 321/347
Qualification Procedure and welders per ASME IX, with the PQR available on request

Two of those rows are where purchase orders quietly go wrong. The interpass cap is often written as "ambient" by suppliers who have not qualified a thick-wall PQR, and the solution anneal is sometimes substituted with a simple pickle-and-passivate, which does not restore corrosion resistance in the heat-affected zone.

Radiography is not one number

If the pipe is ordered to an A358-type specification, "100% RT" is not a complete requirement. The class decides how much of the weld is examined and how the filler passes are treated:

  • one class requires full-length radiography of both sides of a double-welded seam;
  • another requires the same welding but no radiography of the filler passes;
  • a further class allows single-welded seams with partial examination at a defined frequency.

Quoting "we do 100% RT" without the class is therefore ambiguous in both directions: it can mean more inspection than you need, or less than you assumed.

What to put in the RFQ

If you are buying in this size range, five lines in the enquiry save weeks later:

  1. OD, wall thickness, grade and length — with the section length and the number of girth seams stated;
  2. the seam map: how many longitudinal and circumferential welds, and where;
  3. the A358 class (or the equivalent RT/UT scope) written out in full;
  4. heat treatment: solution anneal or stabilisation, with the temperature range;
  5. the document set: EN 10204 3.1 mill certificates, WPS/PQR, RT/UT reports, and any third-party inspection (SGS, BV, TUV).

Reference pages

Written by the technical team at Shiwang Pipe, a stainless steel welded pipe manufacturer in Qingzhou, Shandong, China. We form and weld to 5000 mm OD, up to 80 mm wall.

Top comments (0)