An in-line water purifier removes sludge and dirt from your water supply. This type of water filter, often called the whole house water filter, is installed on the inside wall and the water enters the main faucet before it reaches any plumbing fixture, water heater or refrigerator. Water softener does not replace the well system. In the absence of a water filter, contaminants accumulate in the pipes և can adversely affect the operation of any device. Installing a water filter can significantly extend the life of any equipment.
A typical household water purifier has three parts: a manifold, a filter unit, and a filter. Most household water purifiers use a variety of bottle filters. The filter slides into the container. The bottom of the container cleaning manifold is screwed. The amount of impurities removed depends directly on the type and age of the filter used. There are many types of filters. A simple filter that simply removes rust and debris, from high quality cleaning filters to kills some bacteria and parasites.
Before an entire home for water purification, compare the sbuyingize of the pipes in your home to the collector’s relationship. The collector must have a device the same size as the tube. Most homes use 3/4 or 1 inch pipes. A water purifier with a smaller door prevents the flow of water. Larger gates require a bush or other pruning.
*Install water purifier throughout the house
*
Where you install the water purifier throughout the house depends on the type of plumbing and the water heater in the house. Ideally, a water purifier will connect the home's water supply between the home's main water tank and the front pipe or water-using appliance. Most homeowners find that the best place to access a water line is near a water heater. It will be easier to find a good place for future filter maintinance .
Open the filter installation package and check the system. Look for indicators in large groups. Arrows indicate how water flows through the system. Remember this arrow when repairing water filter from the main pipe to the cleaning area.
Paste the structure of the water purification bracket on the wall, if you have one. If the water cleaner does not have a model, place the water filter cover on the entire house pipe in the inner wall and follow the screw holes in the wall. Some cleaners have holes in the area; Others have different brackets. Leave the brackets installed. Place the test hole on the wall using a marker on the wall or a figure as a guide. If necessary, insert the correct dowel into the test hole. Floor anchors require anchors and anchors. Place the screw holes of the bracket on top of the test holes or anchors. Attach the water purification lid to the wall with a suitable screw.
*Connect the water purifier to the home water pipe.
*
Check the piping and make sure there is free space for all pipes and fittings. Disconnect power from the water Purifier and turn off the water supply. If you are using a well pump in your home, turn off the pump motor circuit breaker. When the house is connected to the municipal water meter, close the main water valve. Open one of the hoses in the house and release the water pressure from the pipes.
Using a proper cutting tool, remove a 5-6 inch section of main water pipe between the first tee and the point where the pipe enters the housing. Leave at least 2 inches of white tube on each side of the cutting. The two-inch pipe section has enough space for the pipe installation required to connect the water filter.
Insert the 90 degree elbow into the main water line that goes into the house and place the elbow manifold door at the entrance to the sewer. Run the pipe from the elbow to the sewer inlet and attach the pipe to the wall. The type and number of equipment and pipes required depends on the location of the washing machine installation and the type of pipe used. If you are using a PVC or CPVC pipe with attachments, cover the connections with the pipe before using the PVC connections. The flowers soften the surface of the tube with elasticity, which helps to seal it with cement. If you use PEX or copper pipes and fittings, remove dust and rust before making the connection. Most homeowners choose to use plumbing fixtures when working with CPVC, PEX or copper pipes. The video pump does not require glass or vibration, glue, origin or ring and does not have a pressure gauge. The arrow at the top of the tank indicates the opening of the entrance.
Connect the drain hose to the end of the two-inch T-Mount hose. Try not to let the outlet pipe pass through the suction pipe and close the wall tightly. If the exhaust pipe must pass through the inlet pipe, use the device to pass through the exhaust pipe.
Make two holes in the wall for each pipe. The straps prevent the pipes from vibrating. Tie each long piece of pipe every four feet as needed.
The sealing ring of the water purifier on the whole-houseshould be lubricated throughout the house with water-free and safe-to-eat grease. Store the water filter in a container. Pull the tank manually into the water purifier by rotating the tank for an hour. At the end of the box, if necessary, unfold the sheets of paper and move the box until it tightens.
Turn on the water supply in your home. Open the hot and cold sides of each tap. Turn on the tap until all the air comes out of the water pipe.
Check each water connection for leaks and repair if necessary. The best way to fix a leak is to replace the leak accessory. Patches don't last long, and in most cases they fail in the worst case. If you want to connect the threaded fitting to the entire household water purifier, cut a tube about 1 inch from the threaded fitting. Remove the threaded joint from the water filter manifold and clean the threaded sealer from the joint and the manifold. Apply thread sealant. Thread sealing paste is a completely reliable way to protect and seal plumbing threads. Just fill the first third of the fixing threads with the paste. Tighten the fitting with a wrench and reconnect the pipe with a joint. Turn on the water and check the system.
When all of your home's water purifiers have passed the leak test, blow the air out of the pipes in your home. Remove as much of the carpet as possible from the water filter, which is often a pipe connection to the outside. Keep turning the faucet until it stops blowing air. This may take a few minutes. Repeat this with every touch, working water purifiers throughout your home. Typically, a homeowner with plumbing knowledge and skills can complete the entire installation process in under three hours, in some cases less than an hour.
*Water purifier recovery
*
Follow the manufacturer's instructions for cleaning the water to make sure your home water is safe. This usually requires a change of filter and O-ring anointing every three or six months. Applying less oil each time the filter is adjusted significantly increases the service life of the O-ring.
Before ringing, look at the O rings on the nicks or on the areas that have been seriously damaged. Alternative container O-rings are available online. Some local stores have large O rings and large O rings. Select the O ring that fits the size of your container. The mistaken O-ring comes out.
Use the filter cover to remove the grains. The wide open end of the valve moves from the end of the box into the hole next to the bracket. Compressing the box next to the box prevents damage.
Top comments (1)
Hi, whole house water filtration systems are becoming an increasingly popular choice for providing clean and safe drinking water in the home and I highly recommend choosing those systems that will be reliable as your health depends on it . I personally recommend whole house systems filterway.com/whole-house-systems/ . These systems are designed to eliminate various contaminants ensuring that families have access to high quality water at every tap. Let's take a look at