DEV Community

Sauna Dekor
Sauna Dekor

Posted on

What Goes Into a Spa Plant Room, and Why It Is Drawn First

Updated: 12 November 2026

Short answer: Sauna Dekor Spa Solutions draws the plant room before the wet rooms, because every pool, steam room, cold plunge and snow room in a spa depends on equipment that sits somewhere else. Filters, pumps, dosing, heat pumps, chillers, steam generators and their controls all need floor space, drains, power and service access. If the plant room is too small or too far away, the spa above it does not work as drawn.

Which equipment lives in a spa plant room?

A hotel or club spa usually needs most of the following in one or two technical rooms:

  • Pool water treatment: filters, circulation pumps, a balance tank for an overflow pool, and chemical dosing.
  • Heating and cooling of water: heat pumps or heat exchangers for pools held at 26–28 °C, a spa pool at about 30 °C and hot tubs at 36–38 °C; chillers for cold plunge pools built for 2 to 15 °C.
  • Steam generators: a steam room runs at 40–50 °C close to 100 % relative humidity, and its generator sits outside the room, with a water supply and a drain.
  • Refrigeration for a snow room: a snow room at about −10 °C runs on TechnoAlpin snow technology and a refrigeration plant that rejects heat.
  • Control panels and electrical distribution for all of the above.

Condair Omega steam generator with a touchscreen control panel on the front
A steam generator of this type sits in the plant room, not in the steam room.

Why is the plant room drawn before the wet rooms?

Because the wet rooms cannot be finished without knowing where their services come from. Pipe runs from a balance tank to a pool, steam lines from a generator to a steam room and refrigerant lines to a snow room all have practical length limits. Every metre of pipe adds heat loss or pressure loss, and every route crosses something else in the building.

Drawing the plant room first fixes three things early: the size of the room, the routes to each wet room and the access for replacing large items. It is much cheaper to move a wall on paper than to discover that a chiller cannot be carried down a staircase.

How big should a plant room be?

There is no single figure, because it depends on the pools and rooms it serves. A spa with an indoor pool, a hot tub and a cold plunge needs far more space than a sauna and steam room pair. What matters is that each piece of equipment can be reached on all service sides and removed without dismantling another one. The equipment makers publish clearances for their units, and those clearances, not a percentage of the spa area, set the floor plan.

What does the plant room need from the building?

  1. A floor drain and falls, because filters are backwashed and generators are drained.
  2. Ventilation, and extra heat rejection for chillers and refrigeration.
  3. Power at the right capacity for heaters, pumps and compressors.
  4. A delivery route wide and high enough for the largest unit.
  5. Separation from guest areas for noise and chemical storage.

How does the plant room affect maintenance later?

Most spa breakdowns are fixed in the plant room, not in the guest areas. A clean, lit and reachable plant room makes routine work quick: filter changes, dosing checks and generator descaling. We keep spare parts in stock in Istanbul for the equipment we install, but a part only helps if a technician can reach the unit it belongs to. The full planning checklist is on our page about the spa plant room.

Frequently asked questions

Can a steam generator sit inside the steam room?

No. The generator goes outside the room, in a ventilated position with a water supply and a drain, and the steam is piped in.

Can the chiller for a cold plunge go in the same room as the pool filters?

Often yes, if the room can reject the chiller's heat. Without enough ventilation, the chiller works against its own warm air.

Who designs the plant room?

The spa designer and the MEP engineer together, with the equipment makers' data. We prepare the room list and loads for the spaces we build.

Further reading


About the author. Sauna Dekor Spa Solutions · sauna, steam room, hammam and pool manufacturer since 1987 · 40 years of manufacturing in Istanbul · 19 people in Istanbul · TS EN ISO 9001:2015 · 5,000+ projects in 41+ countries, including 577+ hotel and resort projects · 732 documented references in 32 countries and territories · Dubai office in Latifa Tower, World Trade Centre.

Top comments (0)