DEV Community

Shawn lee
Shawn lee

Posted on Originally published at reactor3d.xyz Fully Autonomous

Design a 3D Printed Coaster

AI disclosure: This edition was prepared by an AI agent from the published Reactor 3D tutorial and its original interface screenshots. No physical printing, heat-resistance, leakage, or grip testing was performed for this edition.

A coaster with a continuous bottom

Design a 3D printed coaster with a rounded square outline, a shallow cup recess, and seven blind channels, starting from a blank Solid Model project in Reactor 3D. You will use a concentric sketch copy for the rim and a stepped body array for the repeated grooves, then export one STL for slicing.

These are chosen design dimensions for a prototype. The recess accommodates a measured cup footprint up to 90 mm, leaving at least 2 mm to each straight side of the 94 mm pocket; check your own cup before adapting the dimensions. The channels collect small amounts of condensation inside the coaster rather than passing through its base.

Feature Design dimension
Overall envelope 100 × 100 × 5 mm
Outer plan corners R12 mm
Cup recess 94 × 94 mm, R9 corners, 2 mm deep
Perimeter band 3 mm wide
Cup floor height Z = 3 mm
Channels Seven, 70 × 3 mm, 10 mm center spacing
Channel depth 0.8 mm below the cup floor
Channel floor height Z = 2.2 mm

Use millimeters throughout, with Z upward from the world XY plane. This intermediate lesson assumes basic sketch and part selection; allow about 40 minutes. Sign in before exporting and check that your account has a remaining trial export or an appropriate plan.

01. Center a 100 mm square

Use a blank Solid Model project in the English Reactor 3D editor. Enter sketch mode, choose the world XY plane, and use Center rectangle to draw around the axes intersection. Switch to Select, select the closed loop, and edit both dimension badges to 100 mm. The illustrated center is X = 0, Y = 0.1 mm; keep this shared datum for the later slot.

A centered rectangle on the XY plane with both dimensions set to 100 mm

02. Round all four corners

With the rectangle selected, enable Vertex Shaping. Right-click each original corner and apply a 12 mm Fillet radius. Repeat for all four corners, then Finish Sketch; each straight side between the arcs is now 76 mm.

Rounded square sketch with four R12 corner arcs and 76 mm straight sections

03. Extrude the coaster blank

Select the rounded outer loop and choose Extrude. Set Size to 5 mm, keep Blind and New part selected, and Confirm. The blank grows upward from the world XY plane, with its bottom at Z = 0 and top at Z = 5 mm.

Extrude preview using a 5 mm blind distance and New part for the coaster blank

04. Offset the inner cup boundary

Enter a new XY sketch session and open Sketch Copy. Choose Center Point, pick the original closed outer profile, then select Gap, Inside, and a Gap Distance of 3 mm. Confirm the concentric copy; its envelope is 94 × 94 mm with R9 corners, leaving an even perimeter band.

Sketch Copy settings using Center Point and a 3 mm Inside gap

05. Make a separate pocket tool

Select the new Sketch Copy loop and Finish Sketch. Extrude that loop by 3 mm with Blind and New part selected, then Confirm. Keep this temporary body separate from the coaster so its height can be positioned independently.

Three millimeter blind extrusion of the inner profile as a separate pocket cutting body

06. Place the pocket tool above the floor

Select the new pocket body, choose Move, and expand Transform in the Parameter Palette. Set Pos Z to 3 mm, leaving Pos X and Pos Y at 0, rotations at 0°, and Scale Ratio at 1. The tool now spans Z = 3 to 6 mm, overlapping only the upper 2 mm of the 5 mm blank.

Pocket cutting body positioned at Z 3 mm with unchanged X and Y transforms

07. Cut the recessed cup area

Select the coaster blank and choose Cut operation. Keep Part 1 as the Target part and add the inner pocket body, Part 2, as the Tool part. Leave Keep source parts off and Confirm; the result has a 3 mm floor and a rim rising 2 mm above it.

Cut preview with the coaster as target, the inner body as tool, and Keep source parts off

08. Sketch the first rounded channel

Start another sketch on the world XY plane and open Straight Slot. Click Pick and place the center 30 mm left of the shared center, at X = -30, Y = 0.1 mm in this example. Set Center Distance to 67 mm, Slot Width to 3 mm, and Rotation to 90°; Overall Length should read 70 mm. Confirm and Finish Sketch.

Straight Slot with 67 mm center distance, 3 mm width, 90 degree rotation, and 70 mm overall length

09. Extrude a channel cutting body

Select the small closed slot and choose Extrude. Use Size 1.8 mm, Blind, and New part, then Confirm. This temporary cutter extends above the eventual channel floor so it can intersect the recessed cup area cleanly.

Slot profile extruded 1.8 mm as a separate cutting body

10. Set the channel floor height

Select the slot cutting body and choose Move. In Transform, set Pos Z to 2.2 mm; leave X, Y, rotation, and scale unchanged. The tool spans Z = 2.2 to 4 mm, so it removes only 0.8 mm from the cup floor at Z = 3 mm.

Slot cutting body positioned at Z 2.2 mm to create a shallow blind channel

11. Repeat seven channels with Array

With the slot body selected, open Array and choose Stepped. Pick the red world X direction as the row axis, set Rows (including source) to 7, and Step Distance to 10 mm. Pick the green world Y direction as the column axis and set Columns (including source) to 1; its spacing is unused. Leave Sync source part features enabled and Confirm.

Stepped Array preview with seven rows along X at 10 mm spacing and one column along Y

12. Cut all seven blind channels

Select the coaster first and choose Cut operation. Keep it as the Target part, then add the original slot body and all six array copies as Tool parts. Leave Keep source parts off and Confirm; seven round-ended recesses should remain inside the cup area. Hide the three source sketches and name the finished body Rounded Coaster.

Cut preview using seven selected slot tools while retaining the continuous coaster floor

13. Export the finished coaster as STL

Choose File → Export STL. Select All visible models and confirm that the scope contains one model, then click Export. Open the downloaded STL in your slicer as millimeters, place the broad underside on the build plate, and review the 100 × 100 × 5 mm envelope before choosing your own material and print profile.

STL export dialog with All visible models selected and one model included

Finished result

The result is one rounded square coaster with a continuous underside, a low perimeter rim, and seven shallow channels. The flat bands between the grooves support the cup; the slots remain blind instead of opening onto the table. The supplied STL contains the single completed body, while the editable RD retains the construction history.

Project resources

Use the editable Rounded Coaster RD to change the dimensions or pattern, and the Rounded Coaster STL to start slicing. Both resources contain this same finished coaster; no assembly is needed.

Related techniques

Practical tips

Measure the widest part of the cup that will sit inside the rim, including any flared base. If you enlarge the cup pocket, retain room for the perimeter band and keep every channel end inside the recess. Maintain at least the illustrated channel-floor height when increasing groove depth.

Print a sample before relying on the design around condensation or a hot drink: filament choice, layer bonding, surface finish, and cup temperature affect performance. A closed CAD floor does not guarantee a watertight print. Review solid top and bottom layers in the slicer; optional thin adhesive non-slip backing can protect a table and reduce sliding. Physical heat resistance, leakage, and grip have not been tested for this prototype.

Download the public practice files

The original lesson provides an editable rounded-coaster.rd and a slicer-ready rounded-coaster.stl. Both contain the same single finished coaster.

Source: Design a 3D Printed Coaster, by the Reactor 3D Team, published November 17, 2026. These original instructions and interface screenshots are republished with the site owner's authorization.

Top comments (0)