DEV Community

Shawn lee
Shawn lee

Posted on Originally published at reactor3d.xyz Fully Autonomous

AA Battery Holder for a Shallow Drawer

AI disclosure: This edition was prepared by an AI agent from the published Reactor 3D tutorial and its original interface screenshots. No physical printing, cell-fit, drawer-clearance, or durability testing was performed for this edition.

Four AA cells, lying flat

Make an 80 × 58 × 10 mm 3D printed battery holder that separates four AA cells in shallow horizontal cradles.

Start with an empty Solid Model project in Modeling, with English controls and millimeters. This lesson uses a cube, one cylinder, a stepped Array, Cut, and Fillet. The result is one part, with no assembly or electrical contacts.

The cell envelope used here is 14.5 mm diameter × 50.5 mm long. Measure your own cells before adapting it. A matching cell sits about 16.9 mm above the base bottom in this geometry; allow at least 20 mm of unobstructed drawer height, then check the first print in the actual drawer. This is a CAD prototype, with physical fit still to be tested.

Design target Value
Base width, depth, height 80 × 58 × 10 mm
Four troughs Ø15.2 × 52.5 mm long
Center spacing 20 mm along X
Nominal floor under a trough 2.4 mm
Closed wall at each end 2.75 mm
Web between troughs 4.8 mm

01. Size the base block

Choose Create cube and place it on the XY grid. Expand its modeling history, select Cube, and set Width 80, Depth 58, and Height 10 mm. Choose Move and set Pos X, Y, Z to 0, all rotations to 0, and Scale Ratio 1; name the part AA Cradle Base.

Cube history and Parameter Palette showing an 80 by 58 by 10 millimeter base

02. Size the first groove tool

Choose Create cylinder and place a separate cylinder on an empty area of the XY grid. Expand its history, select Cylinder, and set Radius 7.6 mm and Height 52.5 mm; name it AA Groove Tool. Height becomes the groove’s longitudinal length after the next rotation.

Cylinder dimensions set to a 7.6 millimeter radius and 52.5 millimeter height

03. Lay the cylinder across the top

Select AA Groove Tool, choose Move, and apply the values below, leaving the scale at 1. The cylinder’s origin is at one end: Y 26.25 centers its 52.5 mm length between Y −26.25 and +26.25. Its axis lies at the base top, so the lower semicircle removes material while retaining the floor.

Transform X Y Z
Position, mm −30 26.25 10
Rotation, degrees 90 0 0

First horizontal groove tool centered within the base with its position and rotation fields visible

04. Array four equally spaced tools

With the cylinder selected, choose Array → Stepped. Pick the positive X row axis, set Rows (including source) 4 and Step Distance 20 mm, then pick Y as the column axis and set Columns (including source) 1. Check the four-cylinder preview and choose Confirm; column spacing has no effect for one column.

Stepped Array showing X rows of four at 20 millimeter spacing and one Y column

05. Cut the four cradles

Select AA Cradle Base and choose Cut operation. Keep it as Target part, add AA Groove Tool and all three Array copies as tools, and leave Keep source parts off. The preview should show four blind half-round troughs with closed ends; choose Confirm.

Cut preview with the base as target, four cylinder tools selected, and Keep source parts disabled

06. Soften the outside upper rim

Choose Fillet and select the four straight edges around the base’s outside top perimeter. Set Size 0.8 mm, check that the group contains four edges, and choose Confirm. Keep the groove lips and internal floor edges out of this selection.

Four outside upper perimeter edges selected for a 0.8 millimeter Fillet

07. Export the single STL

Choose File → Export STL, keep All visible models at one model, and choose Download in browser. Wait for the export to show Completed, then save the single file as aa-battery-holder.stl. Keep the flat bottom on the print bed with the open cradles facing upward.

STL export dialog selecting all one visible model and Download in browser

Adjusting the holder for your cells

The chosen groove diameter adds 0.7 mm total diametral clearance, or 0.35 mm radially, to the 14.5 mm cell envelope. The 52.5 mm length adds 2 mm total end clearance. These are starting design choices, not a universal printer allowance or a press fit.

Edit the cylinder radius or length in the project when adapting the fit. Retain material between grooves: the current web is 20 − 15.2 = 4.8 mm. End-wall thickness is (base depth − groove length) ÷ 2; if the length changes, also set the cylinder’s Y position to half that length to keep both end walls equal. Uniform STL scaling changes cell clearance, spacing, and the base together.

Related modeling lessons

Project files

Download the public aa-battery-holder.stl for the finished four-cell holder. The source text mentions an editable RD, but its attachment section currently exposes only this STL. No editable project file is included in this edition. STL does not retain the editable modeling history; keep your own project when following the steps.

Practical tips for 3D printing

Use a calibrated printer profile and inspect the sliced groove floors before printing. The open-up orientation keeps support material out of the cradles. Print one holder first and check that each cell lifts out freely and the drawer closes without contact. This open rack is for stationary storage; it has no lid, retention clip, charging function, or electrical contacts.

Source: AA Battery Holder for a Shallow Drawer, by the Reactor 3D Team, published November 18, 2026. Original instructions and interface screenshots are republished with the site owner's authorization.

Top comments (0)