DEV Community

Tongda Machinery
Tongda Machinery

Posted on

Sizing a Blow Molding Line From Real Output, Not the Model Name

When engineers size an extrusion blow molding line, the first trap is treating the litre figure in a model name as a production rate. It is not. On a Tongda machine—and on most industrial EBM builders—the model name follows the maximum container volume that machine is built to make. It does not promise containers per hour.

Tongda has supplied extrusion blow molding machines since 1999, with more than 10,000 machines delivered to over 100 countries and a range from 10 mL bottles to 3,000 L water storage tanks. The notes below are for process and project engineers who need a defensible machine count and a utilities plan before the purchase order is cut.

Three figures that actually describe output

Ask the builder to quote these three items against your drawing and your mold—not against a brochure example:

  1. Extruder output, in kilograms per hour
  2. Dry-cycle time for that machine configuration
  3. Accepted pieces per hour on your mold

A dry cycle is not accepted production. Kilograms per hour are not pieces per hour. Pieces per hour only mean something when they are tied to the mold you will run, because cooling, flash, resin, and the operator’s pace all sit between a volume class and the containers you can pack.

Tongda does not publish a capacity table that turns a model name into pieces per hour. Published model pages, where they exist, are the place to read a figure that belongs to that model. Everyday output is not a fixed share of anything in the name. The full framing is here: Real output versus the model name.

An illustrative sketch (example numbers only)

The arithmetic below uses clearly labeled example numbers. They are not Tongda ratings, not a quotation, and not tied to any Tongda model. Replace every blank with figures quoted for your mold.

EXAMPLE ONLY — not a Tongda specification

Plant need:              1,200 accepted pieces / hour
Quoted on your mold:       400 accepted pieces / hour
Machines to discuss:     1,200 ÷ 400 = 3 machines

Check against resin:
  Piece weight (example):     180 g = 0.180 kg
  Line throughput (example):  1,200 × 0.180 = 216 kg/h
  Compare to quoted extruder kg/h for the configuration you chose.
Enter fullscreen mode Exit fullscreen mode

If the plant need is higher than one machine can deliver on that mold, you discuss a second machine, a multi-head or double-station configuration, or a different cavity layout—not a larger litre number in the model name. The litre class only tells you the machine can physically form that volume; it does not size the line.

A useful internal checklist before you send the enquiry:

  • Accepted pieces per hour on your mold: ______
  • Accepted pieces per hour the plant needs: ______
  • Machines to discuss: needed ÷ accepted on that mold
  • Extruder kg/h quoted for the configuration: ______
  • Dry-cycle time quoted for the configuration: ______

Leave the blanks empty until the builder fills them for your product.

Plant utilities: what to confirm before the machine arrives

A blow molding line needs power, compressed air, and cooling water or a chiller before it can run in your plant. Ancillary choices—dryer, crusher, loader, compressor—are sized with the selected model. They are not one size for every machine.

Voltage and frequency

Tongda customizes voltage and frequency to the buyer’s plant power supply. Build the machine for the supply you have; do not assume a retrofit later. Send the plant voltage and frequency with the container drawing.

Air, chiller, and drying

Compressed air (for blowing and for pneumatic movements), chiller capacity, and drying each depend on the machine model. Tongda does not publish one air volume, one chiller size, or one drying-humidity threshold for the whole range. Say whether the resin is one you expect to dry, and whether a crusher should be in the quotation. Those answers are part of model selection, not a number on a general page.

Floor and material flow

Before installation, confirm floor space, how the machine will be lifted in, how resin will be loaded, whether flash will be ground and returned, and how containers will leave the machine. Factory acceptance at Tongda’s plant is not the same event as site acceptance on your floor—utilities and downstream equipment at the plant can differ from the factory trial. Planning questions (without published kW or air tables) are collected here: Plant utilities for a blow molding line.

What to put in the enquiry email

A complete enquiry saves a round of clarification. Include:

  1. Container drawing, resin, and target accepted pieces per hour
  2. Plant voltage and frequency
  3. Whether you want a dryer, crusher, chiller, or compressor included
  4. Anything already fixed on site (for example an existing compressor), described in words rather than assumed to match every model
  5. The three output figures you want quoted on your mold: kg/h, dry-cycle time, accepted pieces per hour

Payment and acceptance are separate topics, but they affect when utilities must be ready. Tongda’s factory acceptance covers machine inspection, running stability, mold confirmation, and product confirmation; payment is 30% advance and 70% before shipment. Ask for those checks to name the mold and product that were actually confirmed.

Why engineers get this wrong

Model names are easy to compare in a spreadsheet. Real output is not. Two machines in the same volume class can be set up with different heads, stations, and cooling. A plant that orders from the litre figure alone often discovers—after deposit—that the accepted pieces per hour on the actual mold do not match the schedule. The fix is boring and effective: demand the three figures on your mold, sketch the machine count with blanks until those figures arrive, and lock voltage, air, and cooling before the crate ships.

For a quotation against your drawing, use: Contact Tongda.

Top comments (0)