The Forlinx OK8275AA-C (powered by the FET8275AA-C SoM) is an industrial-grade SBC built around the 40 INT8 TOPS (Dense) Qualcomm QCS8275-AA. It directly targets multi-stream video concurrency and industrial bus isolation bottlenecks. However, hardware architects must navigate a strict physical constraint: despite utilizing a 699-pin board-to-board connector, it is electrically incompatible with NVIDIA Jetson carrier boards.
How do the Forlinx OK8275AA-C and FET8275AA-C allocate heterogeneous compute and high-speed storage bandwidth for concurrent industrial vision?
The Forlinx OK8275AA-C ensures multi-video decoding and neural network inference throughput by utilizing the top-tier Dragonwing QCS8275-AA processor (rather than the binned QCS8275-AC variant with lower CPU/GPU clocks and only 20 TOPS), paired with 12GB LPDDR5 and 256GB UFS 3.1 storage.
In edge gateway or machine vision IPC designs, concurrent video decoding, preprocessing, and inference heavily contend for memory bus and inter-core bandwidth. The octal-core CPU on the FET8275AA-C utilizes a tri-cluster architecture: two 2.35GHz Kryo Gold Prime (Cortex-A78) cores handle burst loads and main scheduling, two 2.1GHz Kryo Gold (Cortex-A78) cores maintain sustained high-throughput threads, while four 1.95GHz Kryo Silver (Cortex-A55) cores manage background daemons and I/O interrupts.
Compared to traditional eMMC 5.1 solutions, the onboard 256GB UFS 3.1 eliminates I/O blocking when loading large AI weight models or reading multiple local video streams concurrently. However, it introduces a carrier-level multiplexing constraint: the MicroSD slot and the external eMMC pads cannot be enabled simultaneously. At the Electronica 2026 trade fair, an OK8275AA-C dev kit demonstrated this bandwidth margin by processing 4 live USB camera feeds and 32 local video streams simultaneously, overlaying detection results on a video wall, validating the headroom of the 40 INT8 TOPS (Dense) NPU, Adreno 623 GPU, and LPDDR5 subsystem under multi-stream loads.
Thermally, while the SoM supports an industrial -40°C to +85°C operating range, running the 40 TOPS NPU and A78 cores at peak frequency generates significant heat flux. The OK8275AA-C carrier provides a dedicated SoM cooling fan header. Engineering teams designing fanless enclosures or compact DIN-rail IPCs must evaluate their specific compute duty cycle to size heat spreaders or active cooling topologies accordingly.
| Core Module Category | FET8275AA-C SoM Specs (699-pin B2B capability) | OK8275AA-C Carrier Board Implementation |
|---|---|---|
| Processor (SoC) | Qualcomm Dragonwing QCS8275-AA | Provided via FET8275AA-C SoM |
| CPU Architecture | 2× Cortex-A78 @ 2.35GHz (Kryo Gold Prime) 2× Cortex-A78 @ 2.1GHz (Kryo Gold) 4× Cortex-A55 @ 1.95GHz (Kryo Silver) | Same as SoM |
| AI Compute / GPU | 40 INT8 TOPS (Dense) NPU | Adreno 623 GPU | Same as SoM |
| Memory & Storage | 12GB LPDDR5 + 256GB UFS 3.1 | On-SoM storage; Carrier adds MicroSD slot and eMMC pads (Hardware multiplexed via 0-ohm resistor) |
| Networking | 1× RGMII (up to GbE) 1× SGMII (up to 2.5GbE) | 1× GbE RJ45 + 1× 2.5GbE RJ45 M.2 Key-E (Wi-Fi/BT option) + M.2 USB (4G/5G option) |
| Vision & Display Bus | 3× MIPI CSI (D-PHY or C-PHY support) MIPI DSI + DisplayPort v1.4 | 3× MIPI CSI FPC (Matched to Sony IMX577 default) MIPI DSI GPC (Compatible with official 7" 1024×600 display) + DP port |
| PCIe & USB | 1× 4-lane PCIe Gen4 (RC+EP)1× 2-lane PCIe Gen4 (RC+EP) 1× USB 3.1 Gen2 + 1× USB 2.0 | 1× PCIe x4 slot 1× USB-C OTG + 2× USB 3.0 + 1× USB 2.0 Type-A (Partially muxed via S5 switch) |
| Industrial I/O & Serial | RTSS Domain: Up to 4× CAN-FD, 5× QUP, 62× GPIO MD Domain: 16× QUP (UART/HS UART/I2C/I3C/SPI), 133× GPIO | Terminal block exposes 4× Isolated CAN-FD + 2× Isolated RS485 Remaining MD/RTSS GPIOs routed to FPC and pin headers |
| Audio Subsystem | Up to 8× I2S | I2S Codec (Speaker/3.5mm Jack/MIC) + MAX98357AETE+ Amp (4Ω 1.3W / 8Ω 0.8W) |
| Power, Debug & Temp | Power/Dimensions TBD | -40°C to +85°C | 24V DC input | -40°C to +85°C | JTAG header, RTC battery holder, Fan header |
| OS & Kernel | Linux BSP (kernel 6.18.44) | Linux BSP (kernel 6.18.44) (Following Qualcomm Dragonwing Upstream First strategy) |
How does the Forlinx OK8275AA-C ensure RTSS domain isolation and high-speed interface multiplexing in harsh EMI industrial environments?
The Forlinx OK8275AA-C achieves this by physically separating the Microprocessor Domain (MD) from the Real-Time Subsystem (RTSS) at the hardware level, combined with a standard 24V DC industrial power input, 4 isolated CAN-FD ports, and 2 isolated RS485 ports, directly addressing surge interference and bus determinism.
While the OK8275AA-C shares the QCS8275 silicon with the maker-focused Arduino VENTUNO Q, their hardware engineering trajectories are fundamentally different. By utilizing native 24V DC input and isolated terminal blocks, the Forlinx solution eliminates the need for external power converters and signal isolators in PLC cabinets. However, this introduces specific jumper and DIP switch constraints for physical link multiplexing on the carrier board.
Hardware engineers designing custom baseboards based on the official Forlinx schematics must strictly observe the following four architectural details:
-
MD vs. RTSS Hardware Partitioning: The FET8275AA-C SoM strictly divides its serial engines and general I/O into two hardware domains. The Microprocessor Domain (MD) contains 16 QUPs (Qualcomm Universal Peripherals) and up to 133 GPIOs. Standard UARTs feature a 64B FIFO, while specific channels (
QUP0_SE_2/3,QUP1_SE_2/3) can be configured as 128B FIFO HS UARTs. Each QUP can also be configured as I2C, I3C, or SPI (Master/Slave) based on its index. The Real-Time Subsystem (RTSS) independently commands 5 QUP serial engines, up to 62 GPIOs, and 4 native CAN-FD controllers. This hardware partition ensures that time-sensitive CAN-FD polling and sensor data acquisition are not preempted by heavy vision or OS workloads on the Linux main system. - The 699-pin Connector Trap and Signal Integrity: The FET8275AA-C utilizes a 699-pin board-to-board (B2B) connector. Hardware design teams must be explicitly warned: although this connector shares the exact physical footprint of the NVIDIA Jetson AGX Xavier/Orin and Thor T4000/T5000 modules, Forlinx makes no pin-compatibility claims. The FET8275AA-C is electrically incompatible with Jetson carrier boards. Furthermore, the connector exposes 1x 4-lane PCIe Gen4 and 1x 2-lane PCIe Gen4 interfaces (both supporting RC and EP modes); custom routing must strictly enforce PCIe Gen4 differential impedance and trace length-matching constraints. The 3x MIPI CSI interfaces can be flexibly configured in either D-PHY or C-PHY modes (the OK8275AA-C carrier defaults to matching Sony IMX577 modules via FPC connectors).
- USB and Storage Board-Level Multiplexing Mechanics: On the OK8275AA-C carrier, the USB Type-C OTG port (used for firmware flashing) and one of the USB Type-A (USB 3.0) ports are hardware-muxed via an onboard S5 switch. This dictates that during low-level image flashing or debugging, the corresponding Type-A host interface is physically disconnected. Similarly, the carrier's MicroSD slot and external eMMC footprints share the same storage bus, with the physical path selected via a 0-ohm resistor. The storage expansion strategy must be locked in during the BOM population phase.
- Dual Ethernet and Heterogeneous Wireless Extensions: The SoM exposes Gigabit (GbE) and 2.5GbE network lanes via RGMII and SGMII, which the carrier board breaks out into dual RJ45 ports. This satisfies the physical network isolation required between high-speed industrial cameras (2.5GbE) and uplink cloud/MES systems (GbE). Additionally, the carrier supports Wi-Fi/Bluetooth via an M.2 Key-E slot and 4G LTE/5G cellular expansion via an M.2 USB module interface.
Engineering Selection Boundaries (Target Use Cases vs. Hardware Limitations)
To assist system architects in rapid feasibility assessments and risk mitigation during project scoping, here is a definitive guide to the selection boundaries based on the FET8275AA-C and OK8275AA-C hardware specs:
-
Recommended Use Cases (Green Flags):
- Multi-stream Video Aggregation & Edge Inference Hosts: Systems requiring simultaneous processing of up to 3x MIPI CSI cameras (D-PHY/C-PHY supported) and multiple USB/network streams, relying on the 40 TOPS INT8 compute and 256GB UFS 3.1 for local caching and overlay display.
- Harsh Industrial, In-Vehicle, or Railway Edge Control: Deployments mandating operation in -40°C to +85°C environments, utilizing standard 24V DC industrial power rails, and requiring direct integration with actuator/sensor networks via native 4x isolated CAN-FD and 2x isolated RS485 ports.
- Master/Slave Dual-Mode PCIe Interconnects: Architectures that leverage the RC + EP dual-mode capability of PCIe Gen4 (4-lane + 2-lane), allowing the SoM to act as a Root Complex to control FPGAs/capture cards, or as an Endpoint compute accelerator card plugging into an x86 host motherboard.
-
Hardware Constraints & Red Lines (Avoid at all costs):
- Do NOT reuse legacy NVIDIA Jetson carrier boards: The 699-pin connector on the FET8275AA-C only shares mechanical dimensions with the Jetson AGX Xavier/Orin and Thor series. It possesses zero pin-to-pin compatibility; powering it on a Jetson carrier will result in hardware destruction.
- Do NOT specify concurrent read/write operations for MicroSD and carrier eMMC: These two storage interfaces are hardware-muxed via a 0-ohm resistor on the carrier board and cannot be accessed concurrently in software (the SoM's internal 256GB UFS 3.1 is unaffected by this).
- Do NOT plan for concurrent full-load use of the flashing port and dual USB 3.0 ports: Because the USB Type-C OTG (flashing port) and one USB 3.0 Type-A port are muxed via an S5 switch, factory programming or OTG usage physically locks out one of the USB 3.0 host ports.
What is the coverage of the Linux 6.18 BSP and low-level development documentation for the Qualcomm QCS8275 platform?
Forlinx provides a Board Support Package (BSP) based on Linux kernel 6.18.44 for the OK8275AA-C, directly benefiting from Qualcomm's "Upstream First" strategy for the Dragonwing IoT processors, which significantly lowers the long-term maintenance costs of kernel evolution and mainline driver porting.
Historically, industrial engineering teams have hesitated to adopt Qualcomm SoCs due to heavily proprietary, out-of-tree codebases and outdated kernel versions. The QCS8275-AA bypasses this by launching directly on the modern kernel 6.18.44 sequence. Given that the same silicon is already commercialized on the highly visible Arduino VENTUNO Q, and backed by Qualcomm's upstreaming commitments, driver engineers can easily leverage mainline kernel features when integrating standard PCIe peripherals, USB UVC cameras, or network stacks.
Regarding documentation, Forlinx employs a "public basics + gated deep engineering data" strategy. Once hardware development initiates, authenticated clients receive access to the full low-level development suite, including:
- Hardware Design Package: Datasheets, user manuals, SoM Pinmux tables, and OK8275AA-C carrier board schematics and PCB layout files.
- Software & Firmware Package: Linux BSP user guides, low-level driver source code, driver porting guides, and image flashing instructions (utilizing the carrier's JTAG pin header and USB-C OTG channel for low-level bring-up debugging).
High-Frequency Engineering FAQ
*Q: Can I plug the FET8275AA-C SoM directly into an existing NVIDIA Jetson AGX Orin carrier board?*
A: No. While they utilize the exact same 699-pin physical connector, Forlinx does not claim any pin compatibility. The electrical definitions differ, and plugging it in will likely destroy the hardware.
*Q: Can the USB Type-C port and both USB 3.0 Type-A ports on the OK8275AA-C carrier operate simultaneously?*
A: Not completely. The USB Type-C OTG (flashing port) and one of the USB 3.0 Type-A ports are hardware-multiplexed via an S5 switch. Only one can be electrically active at a time.
*Q: What is the core compute difference between the QCS8275-AA and QCS8275-AC variants?*
A: The FET8275AA-C utilizes the top-tier QCS8275-AA, delivering 40 INT8 TOPS. The QCS8275-AC variant is binned with lower CPU/GPU frequencies and halves the AI compute performance to 20 TOPS.
Pricing and Availability Reference
Forlinx has not yet officially announced the launch date or MSRP for the FET8275AA-C SoM and OK8275AA-C dev kit. As a horizontal pricing anchor for the same silicon, the Arduino VENTUNO Q (powered by the same Qualcomm QCS8275 processor, equipped with 16GB RAM and 64GB eMMC) currently retails for $399 USD.
Considering the OK8275AA-C development kit features a higher-spec 12GB LPDDR5 + 256GB UFS 3.1 storage configuration, supports an industrial -40°C to +85°C temperature range, and integrates heavy industrial peripheral circuitry like dual Ethernet (including 2.5GbE) and multiple isolated CAN-FD/RS485 ports, its final production pricing is expected to be noticeably higher than $399. For sample requests and specific quotes, engineers should consult the official Forlinx website product pages.
Originally published on EmbedSBC — embedded systems, SBC and edge-AI hardware analysis.



Top comments (0)