DEV Community

nabbisen
nabbisen

Posted on • Updated on • Originally published at obsd.solutions

OpenBSD Upgrade 7.4 to 7.5

Summary

The OpenBSD project released 7.5 of their OS on 5 Apr 2024 as their 56th release πŸ’«

openbsd release

What's New | Changelog

This post shows how to upgrade OpenBSD 7.4 to 7.5.
The steps are based on their official great guide.

Tutorial

Here is a step-by-step guide with a set of command-lines to run.

🌷 🐑 πŸŒ…

1. Pre-upgrade: Validate and customize

The official tutorial includes Before using any upgrade method section.

Using sysupgrade is usually a good choice.

Validate available disk size

/usr should be greater than 1.1GB.

$ df -h
Filesystem     Size    Used   Avail Capacity  Mounted on
(...)
/dev/sd1e      7.6G    2.5G    4.7G    35%    /usr
Enter fullscreen mode Exit fullscreen mode

OK :)

Validate compatibility with the current usage

See Configuration and syntax changes and Special packages.

The latter this time includes changes around PostgreSQL, which should be upgraded to 16.1.


Backups (Optional)

You might have to create some backups.

Customize upgrade (Optional)

/auto_upgrade.conf is available as the response file.

Of course, you can skip this and go next if it's unnecessary. The default behavior is sufficient in most cases.

Well, the OpenBSD manual page on autoinstall says:

If either /auto_install.conf or /auto_upgrade.conf is found on bsd.rd's built-in RAM disk, autoinstall behaves as if the machine is netbooted, but uses the local response file. In case both files exist, /auto_install.conf takes precedence.

The whole example of /auto_upgrade.conf is like:

Location of sets = disk
Pathname to the sets = /home/_sysupgrade/
Set name(s) = -x*
Set name(s) = +xbase*
Set name(s) = -game*
Set name(s) = done
Directory does not contain SHA256.sig. Continue without verification = yes
Enter fullscreen mode Exit fullscreen mode

In this case, x sets except xbase and game are excluded.

Also, /upgrade.site can be applied.


2. Upgrade with sysupgrade

OK. You must be ready.

* Caution: The command below, sysupgrade, is unable to stop once it is run.

Let's just run it, if ready:

$ doas sysupgrade
Enter fullscreen mode Exit fullscreen mode

It will print out like this:

Fetching from https://cdn.openbsd.org/pub/OpenBSD/7.5/amd64/
SHA256.sig   100% |*********************************************************|  2324       00:00
Signature Verified
INSTALL.amd64 100% |********************************************************| 44889       00:00
base75.tgz   100% |*********************************************************|   408 MB    00:32
bsd          100% |*********************************************************| 25844 KB    00:02
bsd.mp       100% |*********************************************************| 25917 KB    00:02
bsd.rd       100% |*********************************************************|  4575 KB    00:01
comp75.tgz   100% |*********************************************************| 80681 KB    00:05
game75.tgz   100% |*********************************************************|  2733 KB    00:01
man75.tgz    100% |*********************************************************|  7870 KB    00:01
xbase75.tgz  100% |*********************************************************| 58938 KB    00:02
xfont75.tgz  100% |*********************************************************| 22968 KB    00:02
xserv75.tgz  100% |*********************************************************| 15472 KB    00:01
xshare75.tgz 100% |*********************************************************|  4578 KB    00:00
Verifying sets.
Fetching updated firmware.
fw_update: add none; update intel|
Upgrading.
Enter fullscreen mode Exit fullscreen mode

The machine will reboot and upgrade the system. It will reboot again and sysmerge will follow automatically. Then daemons such as sshd will be started as usual. It will print out "Checking for available binary patches...", and you will see "Run syspatch(8) to install:" if there are.

Finally, you will see:

starting local daemons: cron.
Sat Aug 10 17:07:11 JST 2024

OpenBSD/amd64 ... (ttyc0)

login: 
Enter fullscreen mode Exit fullscreen mode

After all, when login is successful, you will see the login message including "OpenBSD 7.5 (GENERIC.MP)".

3. Post-upgrade: sysmerge if necessary

The official documentation describes on them and helps a lot.

In some cases, configuration files cannot be modified automatically. Run

# sysmerge

to check and perform these configuration changes.

It means manually running sysmerge in addition may be sometimes necessary.
Remember you sometimes have to manually merging conf files such as:

  • /etc/login.conf

Run:

$ doas sysmerge
Enter fullscreen mode Exit fullscreen mode

When there is difference to be manually merged, you will see the results first. Then you will be asked:

  Use 'd' to delete the temporary ./etc/login.conf
  Use 'i' to install the temporary ./etc/login.conf
  Use 'm' to merge the temporary and installed versions
  Use 'v' to view the diff results again

  Default is to leave the temporary file to deal with by hand

How should I deal with this? [Leave it for later]
Enter fullscreen mode Exit fullscreen mode

Each of the top 3 options work like:

  • d: to preserve the current file.
  • i: to overwrite it with the new file sysupgrade brought.
  • m: to merge them manually and interactively.

If you type m to start merge mode, you will be asked to type each of them at each difference:

  • l to choose the left diff,
  • r to choose the right.

Then you will see the options to deal with the merged file:

  Use 'e' to edit the merged file
  Use 'i' to install the merged file
  Use 'n' to view a diff between the merged and new files
  Use 'o' to view a diff between the old and merged files
  Use 'r' to re-do the merge
  Use 'v' to view the merged file
  Use 'x' to delete the merged file and go back to previous menu
  Default is to leave the temporary file to deal with by hand

===> How should I deal with the merged file? [Leave it for later]
Enter fullscreen mode Exit fullscreen mode

If you type e, editor will run with the merged file.

If you type i, the merged file will be installed directly:

===> Merging /etc/login.conf (running cap_mkdb(1), needs a relog)
Enter fullscreen mode Exit fullscreen mode

4. Apply syspatch (skippable)

The next two tasks below are usual just in order to update the system, too.

syspatch is an important command to install binary patches officially offered by OpenBSD successively as found to be needed.

$ doas syspatch
Enter fullscreen mode Exit fullscreen mode

5. Update packages

What's new section in the release page also shows "Some highlights" in "Ports and packages". For example, VMM/VMD was improved this time, too.

The command-line below will update all of the packages installed in the machine:

$ doas pkg_add -u
Enter fullscreen mode Exit fullscreen mode

You will see a lot printed out, but should be careful to read, especially the trailings. They may tell there are some important changes or tasks to do. As to me, I always check if fish, my default shell, starts normally, because I have experienced trouble which crashed it with Python upgrade πŸ˜…

6. Configuration and syntax changes

Update some conf as needed to apply what Configuration and syntax changes describes.

There is nothing this time.

7. Remove old files

This is a simple step. All what to do is just follow Files to remove in the official tutorial.

There is nothing this time.

8. Special packages

Check Special packages in the official tutorial. You may use some of:

  • databases/postgresql

9. Reboot

Almost done ! Finally and optionally run:

$ doas reboot
Enter fullscreen mode Exit fullscreen mode

Conclusion

Hope the new system and you enjoy together long :)

With great appreciation to the OpenBSD project and the community.

Top comments (0)