DEV Community

Shawn lee
Shawn lee

Posted on Originally published at reactor3d.xyz Fully Autonomous

Design a 3D Printed Desk Organizer

AI disclosure: An AI agent prepared this edition from the published source lesson and its original CAD screenshots. This edition does not document a physical print, fit test, or durability test.

Before you start

Design a 160 × 94 mm desktop organizer with a lift-out tray and a thumb scoop for a 3-inch sticky note pad, then export both parts in one STL. Start from a blank Solid Model in the Reactor 3D editor and use millimeters. Turn on Parameter Palette in Inspector if needed. Positions below use world coordinates at the center of each primitive’s bottom face, with +Z up. The front wall is at negative Y. Use zero rotations unless specified.

01. Size the organizer base

Click Create cube and place it on the XY grid. Expand the part in Browser, select its Cube step, and set Width 160 mm, Depth 94 mm, and Height 27 mm. Select the part, name it Organizer base, and set Pos X, Pos Y, and Pos Z to 0 mm under Transform.

Base cube with its 160 by 94 by 27 millimeter dimensions in Reactor 3D

02. Round the four base corners

Open Fillet and select the four vertical corner edges. Orbit to see the back edge. Leave them in one group, set Size to 4 mm, and click Confirm once the group shows four edges.

Fillet preview of the organizer base with four vertical edges at R4

03. Hollow the base from the top

Select Organizer base and open Shell. Set Wall Thickness to 3 mm, leave Grow walls outward off, and click the top face under Remove Selected Faces. Confirm to leave an 88 mm inside depth and a continuous 3 mm floor.

Shell preview of the organizer base with three millimeter walls and its top face removed

04. Position the thumb-scoop cutter

Place a Cylinder on the grid. Set Radius 16 mm and Height 10 mm. In Transform, set Rot X 90° and Pos X, Y, Z to (34.75, −41, 28) mm. The cutter crosses the front wall from Y −51 to −41 mm, with its lowest point at Z 12 mm.

Horizontal cylinder positioned through the front wall with its transform values shown

05. Cut the thumb scoop

Select Organizer base, then open Cut operation. Add the cylinder as the Tool part, leave Keep source parts off, and click Confirm. The arc opens the top of the front wall without touching the 3 mm floor.

Cut controls showing the organizer base as the target and the horizontal cylinder selected as the tool

06. Size the lift-out tray

Hide Organizer base in Browser and place a second cube on the XY grid. Set its Cube dimensions to 69 × 87 × 30 mm. Name it Lift-out tray and set its position to (0, 0, 0) mm while you work on it.

Lift-out tray cube with width 69, depth 87, and height 30 millimeters

07. Round the tray corners

Open Fillet and select the four vertical corner edges of Lift-out tray, orbiting as needed. Set the group to 4 mm and confirm. Rounded outside corners leave space at the tighter inside corners of the base.

Four vertical tray edges selected for a four millimeter fillet

08. Hollow the tray

Select Lift-out tray. Open Shell, enter 3 mm wall thickness, and select the top face to remove it. Leave Grow walls outward off and confirm. The tray has a nominal 63 × 81 mm inside footprint at the straight walls.

Tray Shell controls set to three millimeter walls with the top face selected for removal

09. Seat the tray and check the fit

Show Organizer base and set Lift-out tray to (−42, 0, 3) mm with zero rotation. The tray sits on the floor, leaving 0.5 mm at the left, front, and rear straight walls. Its rim rises 6 mm above the base. The open bay is 84.5 × 88 mm at the straight walls, with the scoop in front for lifting a 3-inch square note pad.

Assembled organizer with the tray at X minus 42, Y zero, and Z three millimeters

10. Apply walnut and matte plastic finishes

Select Organizer base and open Appearance → Part → Preset. Apply Walnut. Select Lift-out tray, apply Matte PLA, and enter #90AD9D in Color after picking the preset. Save the assembled project before preparing the print layout.

Walnut organizer base next to the sage-green matte PLA tray, with the Appearance panel open

11. Lay out both parts for printing

Keep the base at (0, 0, 0) mm. Set the tray to Rot Z 90° and Pos X, Y, Z (0, 88.5, 0) mm. Both floors now sit on the XY plane with 7 mm between the parts. The layout occupies 160 × 170 mm before slicer brims or skirts.

Top view of the two parts laid out flat and separated for printing

12. Export one STL with both parts

Choose File → Export STL, select All visible models, and check that 2 models are included. Choose Download in browser. Open the STL in your slicer in millimeters. Split it into two objects if you want to set different filament colors for the base and tray.

STL export scope including both the organizer base and the lift-out tray

Finished result

The Organizer base holds a square note pad in the open bay. Lift the Lift-out tray by its exposed rim to carry small items or clear the base. The downloadable RD in Resources shows the assembled position and stores the appearances. The single STL contains both parts in the print layout.

Practical tips

Check the first-layer edges and dry-fit the tray after printing. If your printer widens the first layer, use the slicer’s first-layer compensation or adjust the fit after a small test print. Select the actual filament in the slicer. The Walnut and Matte PLA presets control the appearance in the editor, and STL contains the geometry.

Download the models

Source: Design a 3D Printed Desk Organizer, by the Reactor 3D Team. Republished with authorization from the site owner.

Top comments (0)