DEV Community

Shawn lee
Shawn lee

Posted on Originally published at reactor3d.xyz Fully Autonomous

How to Design a 3D Printed LED Light Box

AI disclosure: An AI agent prepared this edition from the published source lesson and its original CAD screenshots. No physical printing, fit, light output, or temperature was independently tested for this edition.

What you will build

Model a 120 × 80 × 36 mm desktop LED light box with a removable diffuser, an inset puck seat, and a GTA 6–inspired Miami sunset motif.

Before you start

Start with a blank Solid Model project in the Reactor 3D editor. Dimensions are in millimeters. Move positions below use world X, Y, Z, with Z measured from the bottom of a Cube or Cylinder placed on the XY grid. For each primitive, place it on the grid, edit its dimensions in the Browser, and set its final position with Move.

The housing is sized for the Bambu Lab LED Lamp Kit-001, which is specified at 59 mm diameter × 8 mm height. Measure your cable before using the 6 mm channel.

01. Size the housing blank

Create a Cube on the XY grid. Expand its modeling history, open the Cube feature, and set Width 120 mm, Depth 80 mm, and Height 36 mm. Name it Housing and use Move to set Pos X, Y, and Z to 0 mm.

Housing Cube with 120 mm width, 80 mm depth, and 36 mm height in the Parameter Palette

02. Hollow the housing

Select Housing and open Shell. Set Wall Thickness to 6 mm, leave Grow walls outward off, and pick the top face under Remove Selected Faces. Confirm to open a 108 × 68 mm cavity above a 6 mm floor.

Shell settings with 6 mm wall thickness and the top opening face selected

03. Cut the diffuser seat

Create a Cube cutter 114 × 74 × 4 mm and set its position to (0, 0, 34.4) mm. Select Housing, open Cut, and add the cube as the tool part with Keep source parts off. Confirm to leave a 1.6 mm deep seat and a 3 mm shoulder around the cavity.

Cut preview of the centered rectangular seat around the light box cavity

04. Recess the LED puck

Create a Cylinder with Radius 30 mm and Height 4 mm. Move it to (0, 0, 4) mm and use it to Cut the inner floor of Housing. The 2 mm recess leaves a 4 mm floor and 0.5 mm nominal radial clearance for the 59 × 8 mm LED puck.

Centered circular LED recess visible in the Cut preview

05. Open the cable channel

Create a Cube cutter 6 × 18 × 34 mm at (0, −36, 4) mm. Use it to Cut the housing along the negative-Y wall. The channel joins the puck recess to the outside and opens through the rim, so the cable can be laid in with its USB plug already outside.

Six millimeter wide cable cutter crossing the negative-Y wall and meeting the puck recess

06. Make the diffuser plate

Hide Housing while you work. Create a Cube 113.4 × 73.4 × 1.6 mm, name it Diffuser, and move it to (0, 0, 0) mm. This gives the centered plate 0.3 mm nominal clearance per side in its seat.

Diffuser Cube showing a 113.4 by 73.4 millimeter outline and 1.6 millimeter thickness

07. Engrave the panel lettering

Switch to Top view and start Text Feature. Pick the top face on its centerline, about 17 mm below the plate center. Set Depth to 0.6 mm, choose Engrave, enter NEON COAST, and set Text Height to 10 mm. Confirm when the lettering reads left to right.

NEON COAST lettering preview in Engrave mode with 10 mm text height and 0.6 mm depth

08. Recess the sunset disc

Create a Cylinder with Radius 11 mm and Height 2 mm, then move it to (0, 15, 1) mm. Use it to Cut the top of Diffuser. The 22 mm disc becomes a 0.6 mm deep recess with a 1 mm floor.

Cut operation showing the circular sunset recess above the engraved lettering

09. Pattern three horizon lines

Make an 88 × 1.6 × 2 mm Cube at (0, −7, 1) mm. Select it and choose Array → Stepped. Pick Y for the rows, enter 3 rows including the source and a 3.5 mm step, then choose X for columns and enter 1 column. Turn off Sync source part features and confirm.

Stepped Array preview showing three rows at 3.5 mm pitch along Y, with one column along X

10. Cut the patterned grooves

Select Diffuser as the Cut target. Add the original stripe cutter and its two copies as tools, leave Keep source parts off, and confirm. The grooves, sun, and lettering all leave 1 mm of material beneath them.

Three stripe tools selected against the diffuser in the Cut preview

11. Seat the diffuser flush

Show Housing and set Diffuser to (0, 0, 34.4) mm with Move. The plate rests on the shoulder, its top level with the 36 mm rim. Check that the perimeter gap is even and that the cable channel reaches the exterior.

Assembled pink diffuser inside the purple housing, with Move showing a 34.4 mm Z position

12. Export both parts in one STL

For printing, move Diffuser to (0, 90, 0) mm so both parts sit on the XY plane with 13.3 mm between them. Keep both visible. Choose File → Export STL → All visible models, then Download in browser to export a single STL containing both parts.

STL export scope showing both visible printed parts selected for one file

Finished result

The two printable parts are Housing and Diffuser. The diffuser lifts off to expose the puck seat. Set the puck into the recess with its light facing the panel, route the cable into the open channel, and use the light box face-up. The project dimensions describe the CAD fit. Test your printed fit, light transmission, and temperature with the chosen material and LED puck.

Practical tips

Use an opaque filament for the housing and a light-transmitting filament for the diffuser. Split the STL into objects in your slicer so you can assign materials. Print the housing open-side up and the diffuser with its engraved side up, then check the 1 mm floor beneath the design in layer preview.

Download the model

Download the original STL. The file contains the housing and removable diffuser as separate bodies already arranged flat for slicing. The LED puck and cable are not part of the STL.

Source: How to Design a 3D Printed LED Light Box, by the Reactor 3D Team. Republished with authorization from the site owner.

Top comments (0)