DEV Community

Cover image for Add Authentication to Portman API tests
Andres Moreno for AWS Community Builders

Posted on • Originally published at

Add Authentication to Portman API tests

When creating an API you want to have security to avoid bad usage and incurring cost by unintended use. Whenever we add a security layer to our APIs any automation that we have around it automatically becomes more complex. Portman provides ways to configure authentication to be used when it runs. In this post we will configuring Portman to successfully run against our secure API.

We will be using the API that we already added Portman configuration to in the Get better API testing by using Portman post. First we need to add security to the API so it only allow access to calls made with a valid API key, after that we can configure Portman to use that API Key and successfully make all the requests needed.

Here is the source code for the end result. If you want to follow along clone/download this commit.

Add Security to API Gateway

To add API Key authentication to the API we will be adding the Auth property in the API resource in the SAM template as shown below:

    Type: AWS::Serverless::Api
        StageName: Lambdaless
          ApiKeyRequired: true
            CreateUsagePlan: PER_API
            UsagePlanName: ProductsAPIUsagePlan
            Name: AWS::Include
              Location: ./products-openapi.yaml
Enter fullscreen mode Exit fullscreen mode

We will also be adding the ApiKeyId in the Outputs section to help us retrieve the API Key later

    Description: API Key ApiKeyId
    Value: !Ref ProductsAPIApiKey
Enter fullscreen mode Exit fullscreen mode

Once the API is deployed with these changes, it will now require an API Key to be passed in the header. This will cause the Portman tests to fail with a 403 since it is not providing the header yet. I will not go into any more details around how security works for API Gateway since it is not in the scope of this article.

Get the API Key

There are two ways you can get the API Key that was generated:

  • Go to the console and retrieve it from the API Gateway service
  • With the CLI. Below I will be explaining how to do it from the CLI.
  1. First we need to get the API Id. We can do this by executing the following command:

aws cloudformation describe-stacks --stack-name products-service

The response for this command comes back with the Outputs defined in the SAM template where we have included the ApiKeyId. Copy the value presented in the OutputValue.

  1. Now we need to run following command replacing the --api-key value with the value copied from the previous step to get the API Key that we can include in our headers:

aws apigateway get-api-key --api-key REPLACE_WITH_APIID --include-value

The API Key will be contained in the "value" attribute in the response. Copy this since we will be using it for the portman configuration in a bit.

Add security definitions in the OpenAPI

If you try to run Portman right now you will get 403 Forbidden responses because Portman is not providing an API key to the request. Portman uses your OpenAPI definition to generate and run the tests, if we do not define the securitySchemes it will not know to apply them. So first we need to setup the securitySchemes supported by our API which in our case is only API Key, to do this we will add the following YAML under the components section of our OpenAPI spec.

      type: apiKey
      in: header
      name: X-API-KEY
Enter fullscreen mode Exit fullscreen mode

OpenAPI supports several authenticaton schemes if you wish to learn more about these please look at the OpenAPI documentation here.
Portman currently suports the API Key, HTTP basic auth and HTTP bearer token security schemes.

In OpenAPI you can apply a different security scheme per endpoint, in our case we want to apply the same one across the whole API. To do this we will be adding the root level security property to define it as shown below.

  - ApiKeyAuth: []
Enter fullscreen mode Exit fullscreen mode

If we run Portman again we will still get a 403 response since we are still not telling Portman what API Key to use.

Configure Portman to use an API Key

Portman allows you to configure securityOverwrites in the globals section of your Pormtan config file.
We will be updating ours to include an overwrite for the apiKey.

  "securityOverwrites": {
    "apiKey": {
      "value": "INSERT THE API KEY HERE"
Enter fullscreen mode Exit fullscreen mode

Now if we run Portman we wll get a successful run just as we did prior to adding security to the API.


In this post we successfully tested a secure API using Portman by

  • Adding security to the API
  • Updating the OpenAPI spec to define the type of authentication to be used
  • Configured Portman to successfully include an API key in the header of every request to be able to automate our API testing for secure APIs


Top comments (0)