Under-extrusion means less filament reaches the part than the layers need. In the worst case nothing comes out even though the extruder motor keeps turning. Before changing any slicer setting, it helps to sort what you see into one of four cases, because each one points to a different place.
Read the symptom first
| What you see | What to check first |
|---|---|
| Nothing comes out when the print starts | Nozzle temperature, the path of the filament, a blocked nozzle |
| Less material than expected, gaps between lines | A partial clog, the extruder gears, extrusion conditions |
| The extruder clicks or the filament does not move | Resistance in the feed mechanism or on the way to the nozzle |
| The print starts fine and extrusion stops later | The spool, the filament path, possible heat creep |
A clicking extruder is worth taking seriously. Prusa explains it as the stepper motor suddenly having to push harder than a preset threshold. It tells you the motor found resistance, not where the resistance is.
Blocked nozzle
Anycubic calls a clogged nozzle the most common cause of filament not coming out. The blockage can be partial or total, and material can also jam above the nozzle, inside the hotend.
Bambu Lab proposes a quick test with PLA: set the nozzle to 220 °C, load the filament and press extrude. If the filament drops vertically, comes out relatively long and looks smooth, the nozzle channel is clear and the drive gear is normal. If it is short and rough, the channel is narrowed or the gear is at fault. The number and the test belong to Bambu Lab, so on another machine start from that manufacturer's instructions.
The first remedy is to push filament through a hot nozzle. Prusa's procedure: heat it to 260 °C if you have been using PLA, or 280 °C for higher-temperature materials such as PETG or ASA, wait two minutes and push. If nothing flows, Prusa suggests the nozzle probably needs replacing, and a cold pull is unlikely to work where this failed.
For nozzles that are not high-flow, Prusa also describes an acupuncture needle or a thin wire (0.3 to 0.35 mm) pushed in from below, 1 to 2 cm, and says to wear protective gloves because material can suddenly start to flow. Bambu Lab warns that using a needle may release the internal pressure of the hot end, so it says to wear gloves and not lean over the machine.
If the clog is only partial and some filament still comes out, the usual next step is a cold pull: a filament is pushed in at printing temperature, cooled, and pulled out to drag residue with it. Prusa says it works best with PLA, that you pull straight up and not sideways, and that you should not stop until the filament is completely out. Creality describes what a good result looks like: the tip reproduces the inside of the nozzle, sometimes with dark specks or residue attached. The cooling temperature differs from one manufacturer to another, so use the one in your printer's guide.
The extruder
When the extruder clicks or the filament comes out ground down, the problem can be in the mechanism that pushes it. The manufacturers list debris in the feed gear, a worn or misaligned gear, a motor with too little force and badly set tension. On the Bambu Lab A1 series, the wiki says to take the extruder apart and check that the motor turns smoothly and that the yellow gear is not worn or missing teeth. For other printers, follow the manufacturer's own steps.
Temperature and speed
A nozzle colder than the material needs makes extrusion harder. Creality suggests raising the temperature in 5 °C steps, without leaving what the filament and the printer allow. At high speed the filament may not melt in time. For its high-speed mode, Bambu Lab recommends raising the nozzle temperature by about 10 °C.
Heat creep
Prusa describes it this way: the printer suddenly stops extruding but keeps making the print moves, without reporting any error. Heat travels up the hotend and melts the filament before it reaches the melt zone. Prusa lists a warm room or an enclosure, PLA, a hotend temperature set too high and too little air over the heatsink among the most common causes. Its checks: the heatsink fan must push air inside, not outside, and PLA in a fully closed, unventilated enclosure is very likely to cause problems. Creality suggests better cooling, a lower temperature and a higher speed as ways to reduce it.
Spool and filament path
The simplest check is that the filament leaves the spool without tangles or obstacles. If your printer guides the filament through a PTFE tube, check that it is seated and undamaged.
Wet or uneven filament
Prusa notes that the industry standard for variation in filament diameter is plus or minus 0.05 mm, and lists degraded or wet filament among the causes of clogs and under-extrusion.
What not to do
Prusa says not to heat the nozzle with an external heat source, because it can damage it, and to take the extruder gearbox apart only with the printer cold and switched off. It also warns against touching the hotend when it is hot, as heated parts can cause severe burns. Bambu Lab says to wear an oven glove when the hotend has to be held.
When to contact the manufacturer
If these checks do not solve it, Bambu Lab recommends submitting a support ticket and including pictures or other details of the problem.
Sources
Everything above comes from the manufacturers' own documentation:
- Prusa, "Clogged nozzle", "Under-extrusion", "Extrusion stopped mid-print (Heat creep)", "Cold pull" and "Extruder noises", Prusa Knowledge Base (consulted 04/11/2026).
- Bambu Lab, "3D Printer Clog", "Under-Extrusion", and the A1 and H2S nozzle clog pages, Bambu Lab Wiki (consulted 11/11/2026).
- Creality, "Filament Not Coming Out of Nozzle", "Cold Pull 3D Printing" and "Heat Creep", Creality blog and store (consulted 04/11/2026).
- Anycubic, "Filament Not Coming Out of 3D Printer", Anycubic blog (consulted 04/11/2026).
The full version, in Spanish and with compatible replacement parts for specific printers, is at laprimeracapa.es.
Top comments (0)