DEV Community

La Primera Capa
La Primera Capa

Posted on Originally published at laprimeracapa.es

3D printing problems by symptom: a field guide to what the print is telling you

A print problem is read from the part itself: it lifts off the bed, material is missing or in excess, layers shift or separate, marks appear on the surface, or the supports fail. Each defect points to its own causes. This guide groups them by what you see and says where to start. Where a defect has its own guide, the link goes there.

The part lifts off the bed, or the first layer is wrong

Corners lift while the part grows, or it never sticks. Warping and poor adhesion are told apart by when they show up. Warping lifts the corners as the part grows, because the plastic contracts as it cools, and Prusa ties it mostly to high-temperature materials such as PC Blend, ASA or ABS. If the part does not stick from the first layers, the problem is usually adhesion, for example grease or residue on the plate. Full guide on warping and parts that lift.

The part sticks but the first layer comes out wrong. Lines that do not join, gaps between them or squashed lines usually trace back to the distance between nozzle and plate. Full guide on bad first layers.

Too much filament, or not enough

Nothing comes out, or too little. The cause can be the nozzle, the extruder, the temperature or the filament path. Full guide on printers that do not extrude.

Over-extrusion. The printer lays down more material than planned along the whole part, and the walls come out rough and uneven, with layers that look thicker or squashed. Creality lists a flow rate that is too high, a temperature that is too high and an incorrect filament diameter, in that order. To correct the flow, lower it a little at a time, but the manufacturers disagree on the step: Creality suggests 2 to 5% each time, Anycubic 5 to 10%. Both suggest lowering the temperature in 5 °C steps, and Creality says to measure the real filament diameter with calipers and match it in the slicer.

Layers shift, separate or ripple

Shifted layers. From one layer up, the part sits offset, as if pushed mid-print. A belt tension that is wrong or loose pulleys are among the usual suspects. Full guide on layer shifting.

Cracks or layers that separate. Bambu Lab describes cracks along the Z direction when interlayer adhesion is insufficient and shrinkage is significant, common with ABS, ASA, PC, PET-CF and PA-CF. Prusa says layer separation is mostly caused by an incorrect profile with the wrong temperatures, or too much cooling from the print fan or the surrounding environment. Bambu Lab's improvement methods start with unclogging the nozzle, because a slight clog can interrupt extrusion in one layer and look like a crack. After that: raise the nozzle temperature appropriately or lower the speed, reduce the part cooling fan, and raise the bed by 5 to 10 °C. For ABS, Prusa suggests turning the fans off and printing in an enclosed chamber.

Waves along the whole height (Z banding). Unlike a sudden shift, the defect repeats along the part in bands. Anycubic says Z wobble and inconsistent extrusion are the two main reasons. On the mechanical side it lists checking the Z-axis stepper motor mount, the lead screw (a bent one should be replaced) and the rod coupler. On the extrusion side it lists a clean nozzle and a stable temperature. Polymaker adds that a tall, thin part can wobble, mostly on printers whose bed moves back and forth.

Marks, strands or blobs on the surface

Strands between parts. Fine, cobweb-like strands appear when molten filament keeps seeping out while the head travels from one area to another. Wet filament, retraction, temperature and nozzle condition are the usual causes. Full guide on stringing.

Dots or blobs. These are localized defects, scattered over the surface, while over-extrusion affects the whole part. Bambu Lab says the most common reason for random dots is the seam position set to Random, which in Bambu Studio you change to Aligned or Back. Its second cause is moisture, and it recommends drying all filaments before printing, new spools included.

Ghosting. Prusa says ghosting is typically recognized by several waves that follow after a sharp edge of a model. Creality traces it to tiny mechanical vibrations when the printhead makes sudden turns. Anycubic and Creality list high speed, acceleration and jerk, loose belts or screws and an unstable base. Prusa starts with the X and Y belts, which should be tight enough to sound like a low bass note when plucked, and adds that ghosting can show even with properly tightened belts, because vibrations increase with print speed: reduce the speed and put the printer on a firm surface.

Supports fail or damage the part

Prusa says that if a support breaks, it is likely to cause a failure on the whole print. To prevent it, it suggests avoiding isolated or scarce support towers, reducing the printing speed for supports and using a brim around the support. It also says the default rectilinear pattern is the easiest to remove, while the rectilinear grid is sturdier and less prone to breaking during printing. After printing, Bambu Lab recommends removing supports within 2 hours of the print finishing, especially for moisture-prone PA-type filaments such as PA-CF.

If the problem persists

If the problem is still there, Bambu Lab recommends submitting a support ticket that includes your recent printer logs and pictures or other details. Prusa suggests sending the model to its customer support when a support problem is very particular.

Sources

Everything above comes from the manufacturers' own documentation:

  • Prusa, guides on warping, ghosting, failing supports and layer separation, Prusa Knowledge Base (consulted 03/11/2026 and 11/11/2026).
  • Bambu Lab, "Dots on the print", "Model interlayer cracking" and "Removing supports and potential print damage", Bambu Lab Wiki (consulted 04/11/2026 and 11/11/2026).
  • Creality, "3D printing: under, over and not extruding" and "3D printer ringing and ghosting", Creality blog (consulted 04/11/2026 and 11/11/2026).
  • Anycubic, "3D printer over-extrusion" and "Fix Z banding / wobble", Anycubic blog (consulted 04/11/2026 and 11/11/2026).
  • Polymaker, "Z-Axis Wobble", Polymaker Wiki (consulted 04/11/2026 and 11/11/2026).

The full version, in Spanish, is at laprimeracapa.es.

Top comments (0)