Most Hastelloy pipe enquiries arrive with a grade already written on them. In my experience the grade is usually right and the failure risk sits somewhere else: the weld, the heat treatment, or a purchase order that never says which of those two things is being inspected.
This is a practical note on where the selection actually goes wrong for welded nickel-alloy pipe, and what belongs in the ordering documents.
Why welded, not seamless
Hastelloy is expensive per kilogram and hard to pierce. For anything above roughly NPS 8, a longitudinally welded pipe is usually the only commercially sane route: plate or coil is roll-formed and seam-welded, then sized and straightened. The trade-off is that the seam becomes the feature that decides acceptance, not the base metal.
That is not a weakness if it is managed. It becomes one when the purchase order asks for "Hastelloy C-276 pipe, ASTM B619" and stops there, because B619 tells the mill what the pipe is, not how good the seam has to be.
The four grades that matter
| Grade (UNS) | Chemistry that drives it | Where it earns its place | Where it fails |
|---|---|---|---|
| C-276 (N10276) | ~15-17% Mo, ~14.5-16.5% Cr, W added | Mixed oxidizing and reducing service, chlorides, hypochlorite, seawater, flue-gas desulphurisation | Not the cheapest choice for purely oxidising duty |
| C-22 (N06022) | ~20-22.5% Cr, ~12.5-14.5% Mo | Oxidising acids, chlorine and bleach duty, pulp bleach plants, where weld-zone stability matters | Not a drop-in for pure reducing acid service |
| B-2 (N10665) | ~26-30% Mo, essentially no Cr | Hydrochloric acid, sulphuric acid in reducing conditions, acetic anhydride | Any oxidising or aerated service, including wet shutdowns |
| B-3 (N10675) | Ni-Mo with controlled Cr and Fe | Same reducing duty as B-2 where ductility and thermal stability after fabrication matter | Still oxidising-hostile |
The rule people get wrong: Cr buys oxidising resistance and Mo buys reducing resistance. If the process stream alternates between the two, C-276 or C-22 is the answer. If it is stubbornly reducing, B-2 or B-3 wins, and adding a stainless grade "for cost" is how you get a pitting failure in year two.
Three cases where the grade was right and the pipe still failed
1. Filler metal matched the base metal but not the joint. C-276 welds are normally made with ERNiCrMo-4; C-22 with ERNiCrMo-10; B-2 with ERNiMo-7. Substituting a 625-type filler because it was on the shelf changes the corrosion behaviour of the seam, and the seam is exactly the area the process sees first.
2. No solution anneal after welding. Welded nickel-alloy pipe is normally supplied solution-annealed and quenched, not as-welded, when the service is aggressive. Skipping it leaves Mo-depleted zones and secondary phases in the weld and heat-affected zone that pick up in chloride or acid duty even though the mill certificate says C-276.
3. Acceptance criteria that never left the RFQ. "Radiography per code" is not a criterion. A seam can pass a code-level radiograph and still carry a weld that fails a bend test or a corrosion test.
What actually belongs in the purchase order
- Base specification (pipe vs tube) and grade with UNS number
- Dimensions: OD, wall, length, and the tolerances you will actually measure at goods-in
- Welding process and filler metal designation
- Heat treatment condition: solution annealed and quenched, or as-welded, stated explicitly
- Seam acceptance: RT or UT coverage, plus the reference standard and acceptance level
- Corrosion verification where relevant: ASTM G28 Method A for the Ni-Cr-Mo grades, Method B for the Ni-Mo grades
- PMI on the seam and on the base metal, with the instrument and the elements reported
- Certificate type: EN 10204 3.1 as a minimum, 3.2 if a third party is witnessing
Put those on one page and the mill knows what "acceptable" means. Leave them out and you are buying a chemistry, not a pipe.
A note on supply
For context on what the mill side looks like, the Hastelloy welded pipe product page lists grade and specification coverage for C-276, C-22 and the Ni-Mo grades, and the long-form piece on why the weld rather than the base metal decides acceptance goes deeper into seam quality and testing sequence. If your seam criteria are borrowed from carbon steel practice, the A358 class structure explained is a useful reference for how class of weld and inspection level get separated - the logic transfers to nickel alloys even though the specification does not.
Shiwang Pipe manufactures large-diameter welded pipe in stainless, duplex and nickel alloys, and the practical answer to "which grade" is usually a two-line email once the stream chemistry and the shutdown condition are known.
Top comments (0)