DEV Community

Cover image for How to setup WiFi hotspot in raspberry pi and connect with ESP8266
Iván Moreno
Iván Moreno

Posted on • Edited on

How to setup WiFi hotspot in raspberry pi and connect with ESP8266

#raspberrypi #esp8266 #wifihotspot #arduino

Basic connection between arduino and raspberry pi through WiFi

test-hw

The Hardware is

  • Esp8266 with arduino sdk
  • Raspberry pi 3b+

System requirements

  • arduino-cli
  • picocom
  • python3

Configurations for Raspberry Pi

  • Install raspbian
  • Enable ssh server
  • Upgrade system
  • Configure keys for ssh server
  • Configure the raspberry pi as hotspot
  • Install python3 and set as default python interpreter
  • Copy server code

Configurations for ESP8266

  • Install esp8266 for arduino
  • Copy the code and upload to esp8266 board

Raspberry Pi Setup

Download raspbian buster lite from official repository

$ curl -LO http://downloads.raspberrypi.org/raspbian_lite/images/raspbian_lite-2020-02-14/2020-02-13-raspbian-buster-lite.zip
Enter fullscreen mode Exit fullscreen mode

Write to sd card

$ unzip -p 2020-02-13-raspbian-buster-lite.zip | sudo dd of=/dev/mmcblk0 status=progress
Enter fullscreen mode Exit fullscreen mode

Connect the raspberry pi via Ethernet and HDMI, startup the system and access with user=pi and password=raspberry. Enable ssh service

$ sudo systemctl enable --now ssh
Enter fullscreen mode Exit fullscreen mode

Check what is the ip address and logout from the system

$ ip addr show eth0 # copy ip address
$ exit
Enter fullscreen mode Exit fullscreen mode

Connect via ssh

$ ssh pi@{ip_address}
Enter fullscreen mode Exit fullscreen mode

Add user with the same privileges and groups to pi user, generate password and delete the pi user

$ sudo useradd -m -s /bin/bash --groups $(groups pi | cut -d ' ' -f 4- --output-delimiter ',') new-user
Enter fullscreen mode Exit fullscreen mode

Create password to new-user

$ sudo passwd new-user
Enter fullscreen mode Exit fullscreen mode

Add new-user to sudoers file

$ echo "new-user ALL=(ALL) NOPASSWD: ALL" | sudo tee /etc/sudoers.d/010_new-user-nopasswd
Enter fullscreen mode Exit fullscreen mode

Login to new user

$ su new-user
Enter fullscreen mode Exit fullscreen mode

Check if sudo works

$ sudo apt update
Enter fullscreen mode Exit fullscreen mode

Check groups

$ groups new-user
Enter fullscreen mode Exit fullscreen mode

If everything works, logout and access to new-user with ssh, first logout

$ exit
Enter fullscreen mode Exit fullscreen mode

Generate keys to new-user and copy to raspberry pi

$ ssh-keygen -f ~/.ssh/rpi-key
Enter fullscreen mode Exit fullscreen mode

Copy public key to raspberry pi

$ ssh-copy-id -i ~/.ssh/rpi-key.pub new-user@{raspberry-pi-ip}
Enter fullscreen mode Exit fullscreen mode

Now access to new-user on raspberry pi

$ ssh new-user@{raspberry-pi-ip}
Enter fullscreen mode Exit fullscreen mode

Remove pi user

$ sudo userdel -rf pi
Enter fullscreen mode Exit fullscreen mode

Update and upgrade the system

$ sudo apt update && sudo apt upgrade -y
Enter fullscreen mode Exit fullscreen mode

Reboot the system

$ sudo reboot
Enter fullscreen mode Exit fullscreen mode

Setup hotspot 

Create an access point in raspberry pi

 Diagram                                  +- RPi ---------+
                                      +---+ 192.168.10.15 |          +- ESP8266 ---+
                                      |   |     WLAN AP   +-)))  (((-+ WLAN Client |
                                      |   | 192.168.7.1   |          | 192.168.7.x |
                                      |   +---------------+          +-------------+
                                      .
                                      .
                              .
                 +- Router -----+     |
                 | Firewall     |     |   +- PC#2 --------+
(Internet)---WAN-+ DHCP server  +-LAN-+---+ 192.168.10.11 |
                 | 192.168.10.1 |     |   +---------------+
                 +--------------+     |
                                      |   +- PC#1 --------+
                                      +---+ 192.168.10.10 |
                                          +---------------+
Enter fullscreen mode Exit fullscreen mode

Install required packages

$ sudo apt-get -y install hostapd dnsmasq netfilter-persistent iptables-persistent
Enter fullscreen mode Exit fullscreen mode

Enable wireless access point

$ sudo systemctl unmask hostapd
$ sudo systemctl enable hostapd
Enter fullscreen mode Exit fullscreen mode

Define the wireless interface IP configuration
Configure wlan0 interface in /etc/dhcpcd.conf
Add the following lines

  interface wlan0
    static ip_address=192.168.7.1/24
    nohook wpa_supplicant
Enter fullscreen mode Exit fullscreen mode

Enable ip forwarding in /etc/sysctl.conf and uncomment the following line

 net.ipv4.ip_forward=1
Enter fullscreen mode Exit fullscreen mode

Allow traffic between clients on this foreign wireless network

$ sudo iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
Enter fullscreen mode Exit fullscreen mode

Make persistent changes

$ sudo netfilter-persistent save
Enter fullscreen mode Exit fullscreen mode

Configure the DHCP and DNS services for the wireless network
First create a backup

$ sudo mv /etc/dnsmasq.conf /etc/dnsmasq.conf.orig
Enter fullscreen mode Exit fullscreen mode

Edit /etc/dnsmasq.conf and add the following lines

  interface=wlan0 
  dhcp-range=192.168.7.2,192.168.7.40,255.255.255.0,24h
  domain=wlan
  address=/gw.wlan/192.168.7.1
Enter fullscreen mode Exit fullscreen mode

Set WiFi country
Localization Options -> Change WLAN Country -> choose your country -> finish

$ sudo raspi-config
Enter fullscreen mode Exit fullscreen mode

Ensure wireless operation

$ sudo rfkill unblock wlan
Enter fullscreen mode Exit fullscreen mode

Configure access point in /etc/hostapd/hostapd.conf
Add the following lines

  country_code=MX
  interface=wlan0
  ssid=rpi-hotspot
  hw_mode=g
  channel=8
  macaddr_acl=0
  auth_algs=1
  ignore_broadcast_ssid=0
  wpa=2
  wpa_passphrase=rasp-p@s2w0rd
  wpa_key_mgmt=WPA-PSK
  wpa_pairwise=TKIP
  rsn_pairwise=CCMP
Enter fullscreen mode Exit fullscreen mode

Reboot the system and check connection with new access point

Install python3 and set as default interpreter

$ sudo apt install -y python3
$ sudo rm /usr/bin/python
$ sudo ln -s /usr/bin/python3 /usr/bin/python
Enter fullscreen mode Exit fullscreen mode

Copy pythonServer to raspberry pi

ESP8266 Configurations

Install required packages

  • arduino-cli
  • picocom

Install esp8266 arduino core
First add additional boards in ~/Arduino/arduino-cli.yml and add the following lines

# arduino-cli.yaml
board_manager:
  additional_urls:
    - http://arduino.esp8266.com/stable/package_esp8266com_index.json
Enter fullscreen mode Exit fullscreen mode

Update index

$ arduino-cli --config-file ~/Arduino/arduino-cli.yml core update-index
Enter fullscreen mode Exit fullscreen mode

Search esp8266 boards

$ arduino-cli --config-file ~/Arduino/arduino-cli.yml core search esp8266
Enter fullscreen mode Exit fullscreen mode

Install esp8266 boards

$ arduino-cli --config-file ~/Arduino/arduino-cli.yml core install esp8266:esp8266
Enter fullscreen mode Exit fullscreen mode

Compile and upload the sketch, assuming that port of esp8266 is /dev/ttyUSB0

$ arduino-cli compile -b esp8266:esp8266:nodemcuv2 -u -p /dev/ttyUSB0 arduinoClient/
Enter fullscreen mode Exit fullscreen mode

Test communications

testGift

Init server in raspberry pi

$ python ~/pythonServer/server.py
Enter fullscreen mode Exit fullscreen mode

Init serial monitor for esp8266 board

$ picocom -b 115200 /dev/ttyUSB0
Enter fullscreen mode Exit fullscreen mode

Raspberry pi output 

  Intialize socket server, listen port: 35000
  Connection from: ('192.168.7.17', 59552)
  From connected user: Init connection from ESP8266
  Write response -> hi from server
  From connected user: hi from client
  Write response -> send quit sequence
  Recive disconnect from client
  Close connection...
Enter fullscreen mode Exit fullscreen mode

Arduino output 

  Wait for WiFi... .....
  WiFi connected
  IP address:
  192.168.7.17
  Connecting to 192.168.7.1:35000
  Wait response from server ...
  Server response: hi from server
  You response -> hi from client
  Server response: send quit sequence
  You response -> quit!
Enter fullscreen mode Exit fullscreen mode

Source Code

Top comments (0)

Read next

tomassirio profile image

Turing Pi 2 Home cluster

Tomas Sirio -

yukikimoto profile image

How to generate an executable file for an AI program using SPVM ?

Yuki Kimoto -

cisc0_pete profile image

Rasp-Pi Network ID tool

Peter G. -

ivandelgado profile image

My Journey into Software Engineering #1: Embracing Mistakes

Ivan Delgado -