Build an ESP32 air quality monitor with a live CO2 dashboard

A CO2 monitor is the rare sensor project that changes your behaviour: watch the number climb through a closed meeting room and you will open a window before anyone gets a headache. This build measures
CO2 properly with a Sensirion SCD41, reads temperature and humidity from the same part, and streams all three to a live dashboard with colour-banded thresholds — so a glance tells you whether the air
is fine or stale.

What it doesn't need is the thing most SCD41 tutorials quietly assume: a Home Assistant server running the ESPHome add-on on your network. The ESP32 here posts straight to your own cloud dashboard over plain HTTPS. Nothing local to keep alive, and the readings open from anywhere.

Why the SCD41

Air-quality projects live or die on the sensor, and the cheap default is a trap. An MQ-135 costs two dollars and reports something, but not CO2 in real ppm — it's a metal-oxide sensor that drifts, needs constant recalibration, and can't separate CO2 from other gases. The older MH-Z19 is a real NDIR CO2 sensor and a fine choice a few years ago.

The Sensirion SCD41 is the current answer: a photoacoustic CO2 sensor accurate to about ±(40 ppm + 5% of reading), that also hands you temperature and humidity over the same I2C bus — three variables, one part, no analog guesswork. It's low-power enough for battery builds, and its automatic self-calibration keeps it honest over time. It costs more than an MQ-135, and it's worth every cent the first time the number tells you something true.

What you'll need

• An ESP32 dev board (any common DevKit variant).
• A Sensirion SCD41 breakout (SCD40 works too — slightly lower accuracy, same code).
• Four jumper wires; the SCD41 is I2C, so it's just power and two data lines.
• The Arduino IDE with the ESP32 board package, the Nodrix library, and Sensirion's I2C SCD4x library, both from the Library Manager.
• A nodrix instance with a project and a project token.

Wiring

Pure I2C — four wires, no analog pins, no level shifting (the SCD41 breakout is 3.3V-friendly):

From	To	Wire
SCD41 VDD	ESP32 3V3	Power
SCD41 GND	ESP32 GND	Ground
SCD41 SDA	ESP32 GPIO21	I2C data
SCD41 SCL	ESP32 GPIO22	I2C clock

GPIO21/22 are the ESP32's default I2C pins. The SCD41 draws a brief high current during each measurement, so power it from a stable 3.3V rail rather than a long, thin lead.

The firmware

The SCD41 measures on its own cadence — one reading every five seconds in periodic mode — so the sketch starts it, then reports whatever it has each cycle. The nodrix Arduino library owns the socket and reconnects.

#include <Nodrix.h>
#include <SensirionI2cScd4x.h>
#include <Wire.h>

const char* WIFI_SSID = "your-ssid";
const char* WIFI_PASS = "your-password";
const char* HOST      = "nodrix.you.workers.dev";
const char* TOKEN     = "tok_your_project_token";

SensirionI2cScd4x scd4x;

void setup() {
  Wire.begin();
  scd4x.begin(Wire, 0x62);
  scd4x.stopPeriodicMeasurement();   // clean state after a reset
  scd4x.startPeriodicMeasurement();
  Nodrix.begin(WIFI_SSID, WIFI_PASS, HOST, TOKEN);
}

void loop() {
  Nodrix.run();

  static unsigned long lastReading = 0;
  if (millis() - lastReading >= 30000) {
    lastReading = millis();

    uint16_t co2 = 0;
    float temperature = 0, humidity = 0;
    if (scd4x.readMeasurement(co2, temperature, humidity) == 0 && co2 > 0) {
      Nodrix.send("co2", (int)co2);
      Nodrix.send("temperature", temperature);
      Nodrix.send("humidity", humidity);
    }
  }
}

Worth understanding rather than copying:

• The co2 > 0 guard matters. The SCD41 returns 0 ppm when a measurement isn't ready yet; sending it would draw a false floor on the chart. Skipping keeps the history honest.
• Give it warm-up time. The first readings after power-up settle as the sensor references itself — expect a couple of minutes before the number is trustworthy, and leave automatic self-calibration on so it stays that way.
• Thirty seconds is plenty. CO2 in a room moves over minutes, not seconds. Reporting twice a minute catches every meaningful change and keeps the traffic trivial.
• Pin TLS before you ship. Nodrix.begin() connects encrypted but unverified on first run; add Nodrix.setCACert() for production, covered in [Connect an ESP32 over HTTPS (https://nodrix.live/guides/esp32-https-cloud).

Build the dashboard

Four widgets, each bound to a variable the firmware sends:

Widget	Bind to	Shows
Gauge	co2	live CO2 in ppm, with colour bands
Chart	co2	the day's air-quality rhythm
Value	temperature	room temperature
Value	humidity	relative humidity

Set the CO2 gauge's bands to the levels that mean something: green below 800 ppm, amber 800–1200, red above 1200. Now the dashboard reads at a glance — you don't interpret a number, you see a colour. The chart is the quietly useful part: a room's CO2 has a shape, climbing while it's occupied and closed, dropping when it's ventilated or empty. Once you know your baseline, the anomalies —
the meeting that ran long, the bedroom that never airs out — jump out.

Add the alert

One automation: trigger on a new co2 reading, condition above 1200, action: Telegram — "CO2 at {{value}} ppm — open a window." Add hysteresis so a room hovering at the line doesn't ping you repeatedly: alarm above 1200, and only rearm once it drops back below 900. Both are edited in the dashboard, not the firmware, and the channel swaps to Discord, Slack, or SMS without touching the condition — the full pattern is in [ESP32 notifications (https://nodrix.live/guides/esp32-notifications).

Going further

• Make it portable. On a battery with deep sleep, it's a monitor you carry room to room — swap the socket for wake-report-sleep over HTTP per ESP32 battery life, and budget for the SCD41's warm-up on each wake or use its single-shot low-power mode.
• Add particulates. A PMS5003 alongside the SCD41 adds PM2.5/PM10 — more variables, more widgets, same reporting loop, for a fuller indoor-air picture.
• Watch several rooms. One SCD41-on-ESP32 per room, each reporting co2_bedroom, co2_office, and so on; a widget per room and one shared automation.
• Automate the fix. If a room has a fan or HRV you can switch, add a relay and a NODRIX_WRITE handler and let high CO2 turn ventilation on — closed-loop, the pattern from the smart-home build.

Notes

• No broker, no local server. The board speaks HTTPS; the dashboard is on your Cloudflare account. No Home Assistant, no MQTT, nothing on your LAN to keep alive.
• A sensor you can trust. Real photoacoustic CO2 plus temperature and humidity from one part — no MOX drift, no analog calibration ritual.
• Scales by repeating. One sketch runs a room or a building; add nodes, not complexity.

FAQ

Why the SCD41 instead of an MQ-135 or MH-Z19?

Because it measures CO2 honestly. The MQ-135 is a cheap MOX gas sensor that doesn't report CO2 in real ppm — it drifts, needs constant recalibration, and conflates gases. The MH-Z19 is a genuine NDIR CO2 sensor and a reasonable older choice, but the Sensirion SCD41 is a current photoacoustic CO2 sensor that also gives you temperature and humidity from one I2C part, with ±(40 ppm + 5%) accuracy. For a monitor you'll trust enough to act on, the SCD41 is the right sensor in 2026.

Do I need Home Assistant or a local server for this?

No — and that's the point. Most ranking SCD41 tutorials assume you already run Home Assistant with the ESPHome add-on, which means a local server humming 24/7 just to see a number. Here the ESP32 posts readings straight to your own cloud dashboard over HTTPS. Nothing local to run, and the dashboard opens from anywhere.

What CO2 levels should I actually worry about?

Outdoor air is around 420 ppm. Below 800 ppm indoors is comfortable and well-ventilated; 800-1200 ppm is where drowsiness and reduced concentration start; above 1200 ppm the room needs air, and sustained levels over 1500-2000 ppm are worth fixing. The guide bands the dashboard on those thresholds so a glance tells you whether to open a window.

Why does the SCD41 need a couple of minutes to read correctly?

It self-calibrates and the photoacoustic measurement settles after power-up — early readings can be off until it warms in. Give it a few minutes on first boot, and leave its automatic self-calibration enabled so it re-references to fresh air over days. If you run it somewhere that never sees outdoor-level CO2, disable ASC and calibrate manually instead.

Can one board watch several rooms?

Not one board, but one dashboard. Put an SCD41 on an ESP32 in each room, have each report co2, temperature, and humidity under its own variable names, and add a widget per room. The automations and alerting are shared — the pattern scales by repeating the node, not by rewiring anything.

---

Originally published on nodrix.live. nodrix is an open-source (MIT) IoT platform you deploy to your own Cloudflare account — source on GitHub.